Zebra Technologies PR4T manual Close the Media Cover, Printer pg

Page 19

Figure 7.4-Close the Media Cover

Figure 7.5- Insert Media into Peeler

P4T/RP4T User Guide

Manual Introduction	RP4T Printers 35
pg.	pg.
4
P4T Overview- pg. 5	Maintenance pg. 36
Printer pg	Troubleshooting 38

Pull Media out of the Printer. Use alignment marks on the cover to ensure alignment.

Close Media

Cover

Peeler Assembly.

Peeler Bar.

3.Feed the leader over the peeler bar and into the printer if you will be peeling labels as you print.

4. Press down on Peeler Assembly where shown and slide the media until it emerges .

1. Remove enough

labels from the media

roll to create a 4” [100

mm] leader.

2. Align the edge of the leader with the index marks on the top cover to ensure it will pass through the peeler without wrinkling.

Preparation . 7	pg.
Connecting the Printer pg. 27	Speci†cations pg. 43
Radio Regulatory Information pg. 31	Appendices pg. 46
	Index pg. 52

4.Close the Media Cover:

Refer to Figure 7.4.

•Pull the media out of the printer as shown at “1.”

•Close the media cover as shown at “2”, ensuring that it latches securely into place.

•Turn the printer on or press the Feed button if the printer is already on.

•The printer will advance a short strip of media and will then be ready for printing.

5. Using the Label Peeler

Optional Step for label stock only

Refer to Figure 7.5.

The label peeler feature allows automatic separation of the printed label from its backing.

1.If you wish to use the label peeling feature, remove enough labels from the media roll to create a leader approximately 4” [100 mm.] long.

2.Align the media as it emerges from the printhead with the index marks on the top cover to ensure it will pass through the peeler assembly without wrinkling.

2.Feed the leader you created in step 1 over the peeler bar and into the peeler assembly.

3 Push on the peeler assembly where shown in Figure 6.5. Insert the leader into the label peeler as shown and push on the media roll until it emerges from the slot at the rear of the peeler assembly.

•Turn the printer on or press the Feed button if the printer is already on.

•The printer will advance a short strip of media and will then be ready for printing.

Section Continues

19

Image 19

Contents UMAN-P4T-013 Rev.A Manual Introduction RP4T PrintersPrinter Preparation pg Index pgProprietary Statement Document Conventions RP4T Printers 35 Manual Introduction Introduction to the P4T SeriesUnpacking and Inspection Reporting DamageP4T/RP4T Overview Printer Preparation pg Troubleshooting pgUSB Port Thermal Transfer P4T Series TechnologyRadio Regulatory Information pg Appendices pg Index pg Direct ThermalCharger Safety Battery SafetyPrinter Preparation LI72 Charger AT17696-xx Single Battery ChargerApproved Chargers Unauthorized equipmentIndex Battery Charging Receptacle P4T Series Battery PackLI72 Battery Charger Connecting Printer Speci†cationsInput Voltage Maintenance pgP4T Series Battery LED Status Charger StatusP4T Series AC Adapter Protective cover For access to Charger ReceptacleVaries with LocationP4T Series DC Adapter DC Power Cord open wiresP4T Vehicle Cradle DC Adapter Access the charger receptacle located on the bottomVehicle cradle as Indicated Installation Guidelines DC Adapter You to monitor the charging process per Indicators under each battery will allowTable below Installing the P4T Series Battery Pack Installing the P4T Series Battery PackLoad the Media Media Spacer Rear Feed Slot External Media Source Loading Media From An External SupplyPrinter pg Close the Media CoverAdjusting The Media Support Disks Close the media cover and ensure it latches in place Close the Printer CoversPast the printhead CoverOperator Controls Printer ControlsTion for more information on the printer status icons Function Default setting Scroll & Select Options Programmable LCD SettingsWlan ID Pull Strap here Adjustable Shoulder StrapSnap into feature on printer Hold Buckle To lengthenProper working order. You can do this by printing a con Verify the Printer Is WorkingBefore you connect the printer to your computer or Portable data terminal, make sure that the printer isCable Communications Connecting the PrinterDetails ConnectorConnector Connector ConnectorCommunications with your printer Connect the Printer by RadioSetting Up the Software Wireless CommunicationsBluetooth Networking Overview Radio Regulatory Information Bluetooth ZBR4 RadioEuropean Regulatory Information for this Radio Europe EU Declaration of Conformity NCC Taiwan Compliance Statement802.11b/g and Bluetooth Co-located Radio Modules Con†guration Rfid optionPrinter Model DigitGeneration 2 Class 1 UHF Passive Tags Supported By The P4T Model RP4T Rfid EncoderExtending Battery Life Preventive MaintenanceGeneral Cleaning Instructions Mechanism P4T Series CleaningTroubleshooting Topics TroubleshootingIcon Status Indication Ref. to Troubleshooting Topic Poor or faded print or low battery icon «ashing Troubleshooting TopicsTo enter Communications Diagnostics Mode Troubleshooting TechniquesTo terminate the Communications Diagnostics Mode Bluetooth radio First diagnostic report for all P4T Series printersSecond diagnostic report for a printer with an End of second diagnostic report Second diagnostic reportCommunications Ports SpecificationsPrinting Speci†cations Memory/Communications Speci†cationsRegulatory pg Index pg Radio Information AppendicesRotation Angles Fonts Available External Media Supply Loading Slot Physical/Environmental/Electrical Speci†cations220,5 mm 57 in ,5mm 80,2 mmPart Number AK18666-1 RW Mod Plug to USB a Cable Manual Introduction RP4T Printers P4T pg MaintenanceAppendix B Appendix C Maintenance SuppliesMedia Supplies Asia Paci†c region, contact Appendix DProduct Support Americas, contactAppendix E Select manual type Click on Submit Appendix FAppendix G- Patents Index UMAN-P4T-013 Rev. a May Zebra Technologies Corporation