Zebra Technologies PR4T manual Radio Regulatory Information, Bluetooth ZBR4 Radio

Page 31

P4T/RP4T User Guide

Manual Introduction

RP4T Printers 35

pg.

pg.

4

 

 

P4T Overview- pg. 5

Maintenance pg. 36

Printer Preparation pg. 7

38

Troubleshooting pg.

Connecting the Printer pg. 27

43

Speci†cations pg.

Radio Regulatory Information pg. 31

Appendices pg. 46

 

Index pg. 52

Radio Regulatory Information

Bluetooth ZBR4 Radio

The following section only applies when the Bluetooth ZBR4 module is installed in a P4T series printer. This radio con†guration has demonstrated compliance to FCC regulations. P4T series printers with this con†guration sold in North America will have the FCC ID:

I28-MD-ZBR4WA and the Industrie Canada ID: 3798B-ZBR4WA for this radio module on a label on the back of the printer.

Caution • Exposure to Radio Frequency Radiation.

The radiated output power of this internal Bluetooth radio is far below the FCC radio frequency exposure limits. The internal Bluetooth radio operates within guidelines found in radio frequency safety standards and recommendations. Do not use the printer in an unauthorized manner.

Note • The following section only applies when the ZBR4 Bluetooth Radio is installed in a P4T Series printer. Unless specified elsewhere in this manual, the antenna used for this transmitter must not be co-located or must not operate in conjunction with any other antenna.

European Regulatory Information for the ZBR4 Bluetooth Radio

This device is intended for use in all EU and EFTA member states. Europe – EU Declaration of Conformity

This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of compliance with the R&TTE Directive 1999/5/EC:

• EN55022

European Immunity Standard

• EN 60950-1

Safety of Information Technology Equipment

• EN 300 328

Technical requirements for spread-spectrum radio equipment

• EN 301 489

EMC requirements for spread-spectrum radio equipment.

This device is a 2.4 GHz wireless LAN transceiver, intended for indoor home and office use in all EU and EFTA member states.

Important Notice:

This device is a portable RF printer intended for commercial and industrial use in all EU and EFTA member states.

WLAN Module Using 802.11b/g Radio

The following section only applies when the 802.11b/g WLAN module is installed in a P4T series printer. Other than conditions speci†ed elsewhere in this manual, only one of the radio options can be installed in the printer at one time and the antenna used for these transmitters must not be co-located or must not operate in conjunction with any other antenna.

P4T Series printers for sale in North America will have the 802.11b/g radio FCC ID:

I28-PLAN11BG, and the Industrie Canada ID: 3798B-PLAN11BG printed on a label on the back of the unit.

Caution • The radiated output power of this internal 802.11b/g WLAN radio is far below the FCC radio frequency exposure limits. The internal radio operates within guidelines found in radio frequency safety standards and recommendations. Do not use the printer in an unauthorized manner.

European Regulatory Information for this Radio

AT

BE

CY

CZ

DK

EE

FI

FR

DE

GR

HU

IE

IT

LV

LT

LU

MT

NL

PL

PT

SK

SI

ES

SE

GB

Note: -Member states in the EU with restrictive use for this device are crossed out!

This device is also authorized for use in all EFTA member states (CH, IS, LI, NO)

Important Notice:

This device is a portable RF printer intended for commercial and industrial use in all EU and EFTA member states except in France where restrictive use applies

Section Continues

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents UMAN-P4T-013 Rev.A Manual Introduction RP4T PrintersPrinter Preparation pg Index pgProprietary Statement Document Conventions RP4T Printers 35 Manual Introduction Introduction to the P4T SeriesUnpacking and Inspection Reporting DamageP4T/RP4T Overview Printer Preparation pg Troubleshooting pgUSB Port Thermal Transfer P4T Series TechnologyRadio Regulatory Information pg Appendices pg Index pg Direct ThermalCharger Safety Battery SafetyPrinter Preparation LI72 Charger AT17696-xx Single Battery ChargerApproved Chargers Unauthorized equipmentIndex Battery Charging Receptacle P4T Series Battery PackLI72 Battery Charger Connecting Printer Speci†cationsInput Voltage Maintenance pgP4T Series Battery LED Status Charger StatusP4T Series AC Adapter Protective cover For access to Charger ReceptacleVaries with LocationP4T Series DC Adapter DC Power Cord open wiresP4T Vehicle Cradle DC Adapter Access the charger receptacle located on the bottomVehicle cradle as Indicated Installation Guidelines DC Adapter You to monitor the charging process per Indicators under each battery will allowTable below Installing the P4T Series Battery Pack Installing the P4T Series Battery PackLoad the Media Media Spacer Rear Feed Slot External Media Source Loading Media From An External SupplyPrinter pg Close the Media CoverAdjusting The Media Support Disks Close the media cover and ensure it latches in place Close the Printer CoversPast the printhead CoverOperator Controls Printer ControlsTion for more information on the printer status icons Function Default setting Scroll & Select Options Programmable LCD SettingsWlan ID Pull Strap here Adjustable Shoulder StrapSnap into feature on printer Hold Buckle To lengthenProper working order. You can do this by printing a con Verify the Printer Is WorkingBefore you connect the printer to your computer or Portable data terminal, make sure that the printer isCable Communications Connecting the PrinterDetails ConnectorConnector Connector ConnectorCommunications with your printer Connect the Printer by RadioSetting Up the Software Wireless CommunicationsBluetooth Networking Overview Radio Regulatory Information Bluetooth ZBR4 RadioEuropean Regulatory Information for this Radio Europe EU Declaration of Conformity NCC Taiwan Compliance Statement802.11b/g and Bluetooth Co-located Radio Modules Con†guration Rfid optionPrinter Model DigitGeneration 2 Class 1 UHF Passive Tags Supported By The P4T Model RP4T Rfid EncoderExtending Battery Life Preventive MaintenanceGeneral Cleaning Instructions Mechanism P4T Series CleaningTroubleshooting Topics TroubleshootingIcon Status Indication Ref. to Troubleshooting Topic Poor or faded print or low battery icon «ashing Troubleshooting TopicsTo enter Communications Diagnostics Mode Troubleshooting TechniquesTo terminate the Communications Diagnostics Mode Bluetooth radio First diagnostic report for all P4T Series printersSecond diagnostic report for a printer with an End of second diagnostic report Second diagnostic reportCommunications Ports SpecificationsPrinting Speci†cations Memory/Communications Speci†cationsRegulatory pg Index pg Radio Information AppendicesRotation Angles Fonts Available External Media Supply Loading Slot Physical/Environmental/Electrical Speci†cations220,5 mm 57 in ,5mm 80,2 mmPart Number AK18666-1 RW Mod Plug to USB a Cable Manual Introduction RP4T Printers P4T pg MaintenanceAppendix B Appendix C Maintenance SuppliesMedia Supplies Asia Paci†c region, contact Appendix DProduct Support Americas, contactAppendix E Select manual type Click on Submit Appendix FAppendix G- Patents Index UMAN-P4T-013 Rev. a May Zebra Technologies Corporation
Top Page Image Contents