Zebra Technologies PR4T Battery Charging Receptacle P4T Series Battery Pack, LI72 Battery Charger

Page 9

P4T/RP4T User Guide

Manual Introduction	RP4T Printers 35
pg.	pg.
4
P4T Overview- pg. 5	Maintenance pg. 36
PrinterPreparation pg. 7	Troubleshooting 38

Figure 3: Charging the P4T Series Battery with the LI72

Battery Charging

Receptacle

P4T Series

Battery Pack

Mains connector will vary with country of intended use.

LI72 Battery

Charger

	pg.
Connecting Printer	Speci†cations

Charging Battery Packs with the AT17696-xx LI72 Single Charger

Plug the LI72 into the appropriate AC wall receptacle, then insert the charge cable into the battery pack charger jack. The yellow/green charge indicator LED will indicate the status of the charger as per the following table.

	Indicator	Charger	Charger Status
		Function

pg.	43
the 27	pg.
Radio Regulatory Information pg. 31	Appendices pg. 46
	Index

	Steady yellow indicator	Standby
	Slow (1 Hz) «ashing	Pre-Charge
	yellow indicator	Pre-Charge
	yellow indicator
	Fast (4 Hz) «ashing	Rapid
	green indicator	Charge
	Slow (1 Hz) «ashing	Maintain
	green indicator	Maintain
	green indicator
	Fast (4 Hz) «ashing	Error
	yellow indicator	Error
	yellow indicator
	Steady green indicator	Ready
	Slow (1 Hz) «ashing
	alternate yellow and	Wait
	green indicator

ACpoweron;nobatterybeingcharged

Chargerisapplyingtricklechargecurrent (5%ofmaximum)tobringacoldbattery temperatureupto0°Cbeforestartinga full charge cycle

Chargerisapplyingthemaximumcharge rate to the battery

Chargerisintricklechargemode(10%of nominal charge value).

The battery may have an internal short, oritschargemonitoringcircuitrymaybe malfunctioning.Thebatterypackshould not be used any further.

Nochargeisbeingappliedtothebattery

Batterytemperatureistoohot.Charging willnotbeginuntilbatterytemperature reaches 45°C.

pg. 52

Notes: The battery pack must be removed from the printer when using the AT17696-xx LI72 Single Charger. Charging will cease three (3) hours after the charger has entered the “Maintain” mode.

Section Continues

Image 9

Contents Printer Preparation pg Manual Introduction RP4T PrintersIndex pg UMAN-P4T-013 Rev.AProprietary Statement Document Conventions Unpacking and Inspection Introduction to the P4T SeriesReporting Damage RP4T Printers 35 Manual IntroductionPrinter Preparation pg Troubleshooting pg P4T/RP4T OverviewUSB Port Radio Regulatory Information pg Appendices pg Index pg P4T Series TechnologyDirect Thermal Thermal TransferBattery Safety Charger SafetyPrinter Preparation Approved Chargers Single Battery ChargerUnauthorized equipment LI72 Charger AT17696-xxLI72 Battery Charger Battery Charging Receptacle P4T Series Battery PackConnecting Printer Speci†cations IndexP4T Series Battery Maintenance pgLED Status Charger Status Input VoltageVaries with Protective cover For access to Charger ReceptacleLocation P4T Series AC AdapterP4T Series DC Adapter DC Power Cord open wiresAccess the charger receptacle located on the bottom P4T Vehicle Cradle DC AdapterVehicle cradle as Indicated Installation Guidelines DC Adapter Indicators under each battery will allow You to monitor the charging process perTable below Installing the P4T Series Battery Pack Installing the P4T Series Battery PackLoad the Media Media Spacer Rear Feed Slot External Media Source Loading Media From An External SupplyPrinter pg Close the Media CoverAdjusting The Media Support Disks Past the printhead Close the Printer CoversCover Close the media cover and ensure it latches in placePrinter Controls Operator ControlsTion for more information on the printer status icons Function Default setting Scroll & Select Options Programmable LCD SettingsWlan ID Snap into feature on printer Adjustable Shoulder StrapHold Buckle To lengthen Pull Strap hereBefore you connect the printer to your computer or Verify the Printer Is WorkingPortable data terminal, make sure that the printer is Proper working order. You can do this by printing a conCable Communications Connecting the PrinterConnector Connector ConnectorConnector DetailsCommunications with your printer Connect the Printer by RadioWireless Communications Setting Up the SoftwareBluetooth Networking Overview Bluetooth ZBR4 Radio Radio Regulatory InformationEuropean Regulatory Information for this Radio Europe EU Declaration of Conformity NCC Taiwan Compliance Statement802.11b/g and Bluetooth Co-located Radio Modules Printer Model Rfid optionDigit Con†gurationGeneration 2 Class 1 UHF Passive Tags Supported By The P4T Model RP4T Rfid EncoderPreventive Maintenance Extending Battery LifeGeneral Cleaning Instructions Mechanism P4T Series CleaningTroubleshooting Troubleshooting TopicsIcon Status Indication Ref. to Troubleshooting Topic Poor or faded print or low battery icon «ashing Troubleshooting TopicsTroubleshooting Techniques To enter Communications Diagnostics ModeTo terminate the Communications Diagnostics Mode First diagnostic report for all P4T Series printers Bluetooth radioSecond diagnostic report for a printer with an End of second diagnostic report Second diagnostic reportPrinting Speci†cations SpecificationsMemory/Communications Speci†cations Communications PortsRadio Information Appendices Regulatory pg Index pgRotation Angles Fonts Available 220,5 mm 57 in ,5mm Physical/Environmental/Electrical Speci†cations80,2 mm External Media Supply Loading SlotPart Number AK18666-1 RW Mod Plug to USB a Cable Manual Introduction RP4T Printers P4T pg MaintenanceMaintenance Supplies Appendix B Appendix CMedia Supplies Product Support Appendix DAmericas, contact Asia Paci†c region, contactAppendix E Select manual type Click on Submit Appendix FAppendix G- Patents Index UMAN-P4T-013 Rev. a May Zebra Technologies Corporation