Zebra Technologies PR4T manual Adjusting The Media Support Disks

Page 20

Adjusting The Media Support Disks

P4T/RP4T User Guide

Manual Introduction

RP4T Printers 35

pg.

pg.

4

 

 

P4T Overview- pg. 5

Maintenance pg. 36

Printer Preparation pg. 7

38

Troubleshooting pg.

Connecting the Printer pg. 27

43

Speci†cations pg.

Radio Regulatory Information pg. 31

Appendices pg. 46

 

Index pg. 52

Media Core Size

Media supplied for the P4T Se- ries printers will have two pos- sible core sizes, depending on the media type. Journal media and most label media is supplied with a 0.75” [19.1 mm] diameter core to maximize the amount of media contained on a roll.

P4T printer media supports are set at the factory for 0.75” diam- eter media cores.

RP4T printers (equipped with the RFID encoder) are configured for media with 1.38” [35.05 mm] diameter cores since RFID me- dia cannot be wound around a small diameter core without both degrading its ability to feed properly past the printhead and causing possible damage to the embedded RFID circuitry.

Figure 8- Adjusting the Media Core Diameter

Changing The Media Support

 

Core Diameter Size

Remove Support Disk,

It may become necessary to

and «ip it 180° to change

change the media core size in

core size.

the field to allow use of different

 

Media Support Disk

media.

The media support disks are

(shown re-adjusted for

3/4” label media core)

designed for both sizes of media

 

 

cores, and they can be adjusted

 

by removing them, flipping their

 

position and re-securing them to

 

the printer.

 

1. Open the Media Cover and

 

remove any label media.

 

2. Use Phillips head screwdriver

 

with a long blade to keep the

 

screw attaching the Support Disk

 

to the printer from turning.

 

3. Rotate the Support Disk while

 

keeping the attachment screw

 

from turning, and remove it.

4. Flip the Media Support Disk so that the desired core diameter ridge faces towards the inside of the printer. Please refer to Figure 8.

 

 

5. Re-secure the Support Disk by tighten-

Media Support Disk

3/ ”

ing it onto the attaching screw. Do not over

(shown adjusted for 1

tighten the Support Disk. It must be able to spin

label media core)

8

 

 

 

 

freely.

 

 

Repeat this procedure on the other Support Disk.

 

 

Always ensure that both Support Disks are adjusted for the

 

 

same size media core.

 

 

Replace the Media Support Disks if they have been adjusted

 

 

for di¨erent core sizes more than 5 (†ve) times.

Section Continues

0

Image 20
Contents Manual Introduction RP4T Printers Printer Preparation pgIndex pg UMAN-P4T-013 Rev.AProprietary Statement Document Conventions Introduction to the P4T Series Unpacking and InspectionReporting Damage RP4T Printers 35 Manual IntroductionUSB Port Printer Preparation pg Troubleshooting pgP4T/RP4T Overview P4T Series Technology Radio Regulatory Information pg Appendices pg Index pgDirect Thermal Thermal TransferPrinter Preparation Battery SafetyCharger Safety Single Battery Charger Approved ChargersUnauthorized equipment LI72 Charger AT17696-xxBattery Charging Receptacle P4T Series Battery Pack LI72 Battery ChargerConnecting Printer Speci†cations IndexMaintenance pg P4T Series BatteryLED Status Charger Status Input VoltageProtective cover For access to Charger Receptacle Varies withLocation P4T Series AC AdapterDC Power Cord open wires P4T Series DC AdapterVehicle cradle as Indicated Access the charger receptacle located on the bottomP4T Vehicle Cradle DC Adapter Installation Guidelines DC Adapter Table below Indicators under each battery will allowYou to monitor the charging process per Installing the P4T Series Battery Pack Installing the P4T Series Battery PackLoad the Media Loading Media From An External Supply Media Spacer Rear Feed Slot External Media SourceClose the Media Cover Printer pgAdjusting The Media Support Disks Close the Printer Covers Past the printheadCover Close the media cover and ensure it latches in placeTion for more information on the printer status icons Printer ControlsOperator Controls Programmable LCD Settings Function Default setting Scroll & Select OptionsWlan ID Adjustable Shoulder Strap Snap into feature on printerHold Buckle To lengthen Pull Strap hereVerify the Printer Is Working Before you connect the printer to your computer orPortable data terminal, make sure that the printer is Proper working order. You can do this by printing a conConnecting the Printer Cable CommunicationsConnector Connector ConnectorConnector DetailsConnect the Printer by Radio Communications with your printerBluetooth Networking Overview Wireless CommunicationsSetting Up the Software European Regulatory Information for this Radio Bluetooth ZBR4 RadioRadio Regulatory Information NCC Taiwan Compliance Statement Europe EU Declaration of Conformity802.11b/g and Bluetooth Co-located Radio Modules Rfid option Printer ModelDigit Con†gurationModel RP4T Rfid Encoder Generation 2 Class 1 UHF Passive Tags Supported By The P4TGeneral Cleaning Instructions Preventive MaintenanceExtending Battery Life P4T Series Cleaning MechanismIcon Status Indication Ref. to Troubleshooting Topic TroubleshootingTroubleshooting Topics Troubleshooting Topics Poor or faded print or low battery icon «ashingTo terminate the Communications Diagnostics Mode Troubleshooting TechniquesTo enter Communications Diagnostics Mode Second diagnostic report for a printer with an First diagnostic report for all P4T Series printersBluetooth radio Second diagnostic report End of second diagnostic reportSpecifications Printing Speci†cationsMemory/Communications Speci†cations Communications PortsRotation Angles Fonts Available Radio Information AppendicesRegulatory pg Index pg Physical/Environmental/Electrical Speci†cations 220,5 mm 57 in ,5mm80,2 mm External Media Supply Loading SlotManual Introduction RP4T Printers P4T pg Maintenance Part Number AK18666-1 RW Mod Plug to USB a CableMedia Supplies Maintenance SuppliesAppendix B Appendix C Appendix D Product SupportAmericas, contact Asia Paci†c region, contactAppendix E Appendix F Select manual type Click on SubmitAppendix G- Patents Index Zebra Technologies Corporation UMAN-P4T-013 Rev. a May