Nortel Networks W/WOL, 21 PCI 10/100 manual Connecting the WOL Cable

Page 29

Hardware Installation

Connecting the WOL Cable

To install the WOL cable between the BayStack 21 network card and the chassis:

1.Make sure that the workstation is disconnected from the power source and the chassis cover has been removed.

2.Connect one end of the WOL cable to the network card WOL connector.

You can use either connector on the WOL cable; they are identical. Refer to Figure 1-3 on page 1-5 for the location of the WOL connector on the network card.

3.Identify the WOL connector location on the workstation motherboard.

The location of the connector is system dependent. You may see “WOL” written on the motherboard.

4.Connect the other end of the WOL cable to the motherboard.

Caution: If the WOL connector on the motherboard does not fit the connector on the WOL cable, or if the WOL connector does not have three pins, do not force the connection or alter the components. Using an incorrect connector can damage the workstation.

5.Replace the chassis.

6.Install a standard Ethernet cable to the BayStack 21 network card.

a.Plug one end of the network cable into the RJ-45 connector of the network card.

b.Plug the other end of the network cable into a port on the network hub.

7.Reconnect the power cord and turn the workstation on.

8.Press the Delete key to enter the BIOS CMOS Setup.

9.Enable the WOL function or the power-on function of the workstation.

The name of this function is architecture dependent. The function may be located in a category heading such as “Power Management.”

10.Test the WOL function from the workstation you just connected or from another remote workstation that has a network card installed.

206379-A

2-3

Image 29

Contents Part No -A September Great America Parkway Santa Clara, CA Trademarks Copyright 1999 Nortel NetworksUSA Requirements Only EN 55 022 StatementVoluntary Control Council for Interference Vcci Statement 206379-A Restricted Rights Legend Nortel Networks NA Inc. Software License Agreement Vii Viii Contents Chapter Using the WOL Feature Appendix B Novell NetWare Reference Information Xii Figures 26. Microsoft TCP/IP Properties Dialog Box Tables Xvi Text Conventions PrefaceBefore You Begin Technical Solutions Center Telephone Number Technical Publications How to Get HelpBayStack 21 PCI 10/100 Adapter w/WOL Overview Chapter IntroductionBayStack 21 Network Card Product FeaturesProduct Description LEDs RJ-45 Ethernet PortDescribes the Link and Activity LED indications WOL Cable and ConnectorSystem Requirements WOL ConnectorSupported Operating Systems Operating EnvironmentsEthernet Cables 10 Mb/s Cable RequirementsFast Ethernet Cables 100 Mb/s Page Package Contents Chapter Hardware InstallationInstalling the BayStack 21 PCI 10/100 Adapter w/WOL Connecting the WOL Cable Page Chapter Software Installation Turn on the power to the workstation, and start Windows PreinstallationInstalling the Network Driver in a Windows 95 Environment New Hardware Found Window-BayStack Network Card Click Next Update Device Driver WizardRemove any CDs from your CD drive Click Yes Click FinishSelect the Identification tab Figure Configuring the Windows 95 EnvironmentConfiguring the Workstation Identification Enter the following information for your workstation System Settings Change Dialog BoxNetwork Dialog Box-Configuration Tab Configuring the Network PropertiesSelect Protocol Click Add Click Add11. Configuration Tab, BayStack 21 Network Card Selected 12. TCP/IP Properties Dialog Box Click PropertiesRemove all CDs from the CD drive Click Yes Installing the Network Driver in a Windows 98 Environment14. New Hardware Found Window 16. Copying Files Dialog Box Select one of the following options 18. System Settings Change Dialog BoxSelect Nortel BayStack 21 10/100 PCI Ethernet Adapter Configuring the Windows 98 Environment20. TCP/IP Properties Dialog Box Select the Adapters tab Figure Installing the Network Driver in a Windows NT EnvironmentClick Have Disk Select Add23. Select OEM Option Dialog Box Select Auto Click OKClick the Protocols tab Configuring the Network PropertiesMicrosoft TCP/IP Properties dialog box opens Figure From the Installation Options menu, select Driver options Installing the Network Driver in a Novell NetWare ServerClick Close TypeSpecifying Driver Parameters Press EnterPress Enter at each of the following four prompts Enter the following commands, in order Installing the Network Card in a Novell NetWare ClientSetting Up the Workstation Chapter Using the WOL FeatureOpen a WOL utility, such as the Magic Packet Utility Figure Running the WOL FeatureMagic Packet Utility identification window opens Figure Send a Magic Packet to One Host dialog box opens Figure Diagnostic LEDs Chapter TroubleshootingSoftware Issues Hardware IssuesTypical PCI Slot Parameters Page Product Specifications Appendix a Technical SpecificationsSoftware Drivers Table A-1. Technical SpecificationsNovell NetWare Server AUTOEXEC.NCF Files and Parameters Appendix B Novell NetWare Reference InformationOne Network Card Installed Slot Parameter Sample AUTOEXEC.NCF File ParametersNode Parameter Sample NET.CFG Files Novell NetWare Client Commands and NET.CFG FileClient Commands Page Numbers IndexIndex-2