Nortel Networks R2MFC manual Module configuration parameters, Parameter Setting

Page 53

Chapter 5 Configuring the R2MFC MBM 53

3Select the appropriate Bus # under Configuration > Resources > Telephony Resources in the navigation tree.

The Bus # information frame displays. See Figure 19 for an example of the screen layout for an R2MFC MBM configured on Bus 2.0.

Figure 19 BCM Bus configuration for R2MFC MBM

4Configure the fields in the Details for Module: 2.0 panel. See Table 7 for parameters and settings.

Table 7 Module configuration parameters

Parameter

Setting

 

 

Trunk type

PRI

 

 

Protocol

Euro

 

 

Clock source

Primary external (if only one

 

trunk module in system;

 

otherwise, it depends on the

 

synchronization scheme of

 

the BCM)

 

 

Overlap receiving

Selected (On)

 

 

Local number length

According to BCM local

 

dialing plan (customer -

 

dependent)

 

Note: This field appears

 

only when the Overlap

 

receiving field is selected.

 

 

E1 Parameters - CRC4

Not Selected (Off)

 

 

R2MFC Media Bay Module Installation and Configuration Guide

Page 52 Page 54
Image 53
Page 52 Page 54
Contents R2MFC Media Bay Module Installation and Configuration Guide North American Regulatory Information SafetyRadio-frequency Interference Enhanced 911 ConfigurationR2MFC Media Bay Module Installation and Configuration Guide Hearing Aid Compatibility Important Safety InstructionsRepairs NN40010-300International Regulatory Information NN40010-300 Contents Chapter Preparing to install the R2MFC MBM Chapter R2MFC MBM maintenance Appendix a Configuring DIP switch settings and definitions MFC Register Signaling Panama Config 1 NN40010-300 Getting Help over the phone from a Nortel Solutions Center How to Get HelpGetting Help from the Nortel Web site Getting Help through a Nortel distributor or resellerHow to Get Help NN40010-300 Audience Getting startedAbout this guide Acronyms Before you beginSymbols and text conventions Convention Example Used for PswdRelated publications Getting started NN40010-300 General information Chapter OverviewOverview Administration and maintenance toolsR2MFC MBM faceplate elements System Status LEDs Config DIP switchesR2MFC MBM back and underside elements BNC and RJ-48 connectorsRS232 port E1 Status LEDsMBM DIP switches Power connectorsOverview NN40010-300 Chapter Preparing to install the R2MFC MBM Host system setup requirements Installation process mapPreparing to install the R2MFC MBM Host system setup requirementsConfig DIP switches R2MFC MBM setup requirementsCustomer supplied hardware requirements Overview of the R2MFC MBM installation Chapter Installing the R2MFC MBMShutting down a BCM 4.0 system Installing the R2MFC MBMShutting down the system Shutting down the BCM 4.0 system hardware Shutting down a BCM 3.7 or lower systemInstalling an R2MFC MBM in the BCM platform base chassis Installing an R2MFC MBMInstalling an R2MFC MBM in the expansion unit Installing the rubber boot in an R2MFC module Installing an R2MFC MBM in the BCM50 expansion unitR2MFC Transmit Co-axial cable connected to the MBM Removing an R2MFC MBM Reconnecting the equipmentRemoving an R2MFC MBM from the BCM platform base chassis How to remove a BCM200 R2MFC MBMRemoving an R2MFC MBM from the expansion unit How to remove a BCM400 R2MFC MBMHow to remove the expansion unit front bezel Wiring an R2MFC MBMInstalling the R2MFC MBM Trunk wiring overview Connecting an R2MFC MBM to a service providerInstalling the R2MFC MBM Configuring the R2MFC MBM Chapter Configuring the R2MFC MBME1 framing MFCR2 side External Link configurable parametersPhysical line characteristics Register signaling Line signalingOption Parameters Meaning Default Minimum or fixed number length + timer parametersSetting Config DIP switches Configuring the MFCR2 external linkCreating a customized country code Config DIP switch layoutE1 framing default parameters PRI side Internal Link configurable parametersSignaling Configuring the PRI internal linkConfiguring the PRI internal link using Element Manager Layer 2 signaling parametersParameter Setting Module configuration parametersBCM lines configuration for R2MFC MBM Configuring the PRI internal link using Unified ManagerModule type BCM module configuration for R2MFC MBM Off Turning on second dial tone Turning on second dial tone using Element ManagerOutgoing dialing configuration for second dial tone Turning on second dial tone using Unified ManagerConfiguring the R2MFC MBM Inter-working functionality Chapter R2MFC MBM maintenanceTranslation of Subscriber Status R2MFC MBM maintenanceClock synchronization Setting the R2MFC MBM to diagnostic mode Diagnostic toolsDiagnostic and loopback modes Mode Description Call AvailabilityAlarms Measurements AlarmsIncoming signal errors Alarms propagationGroup I Alarms propagation Sheet 1 Alarm CauseGroup II alarms propagation R2MFC MBM maintenance Group I Alarms propagation Sheet 2Faceplate LEDs System status monitor LEDsLogs and traces Error messagesLED Name Yellow LED Red LEDReplacing an R2MFC MBM Overview of module replacement processUpgrading firmware Connect using Hyper-terminal setup parametersProgram responds starting rec 0. Hit any key to continue R2MFC MBM maintenance NN40010-300 Overview Chapter Command Line Interface CLIUsers and passwords Command Line Interface CLI Accessing the CLILOad directory CLI commands CommandsINfo directory CLI commands LOad directoryVIew directory VIew directory CLI commandsCNtrl directory CNtrl directory CLI commands Sheet 1NN40010-300 COnfig directory CLI commands Sheet 1 COnfig directoryCNtrl directory CLI commands Sheet 3 NN40010-300 ALarm directory CLI commands Sheet 1 ALarm directoryNN40010-300 SWerr directory SWerr directory CLI commandsMFC directory MFC directory CLI commands Sheet 1MFC directory CLI commands Sheet 2 See Chapter , MFC Signal Definitions, on page 111 for MFC R2 directory R2 directory CLI commands Sheet 1Command Line Interface CLI R2 directory CLI commands Sheet 2 PRI directory PRI directory CLI commandsCommand Line Interface CLI NN40010-300 Shows the Config DIP switch layout Appendix a Configuring DIP switch settings and definitionsSecond dial tone DIP switch settings Country selection DIP switch settingsMexico Config 1 R2 A/B signals Country code defaultsMexico Config Meaning Signal Interpretation of received MFC signalsInterpretation of transmitted MFC signals Sheet 1 Mexico Config Interpretation of received MFC signals Sheet 1 Mexico Config 2 R2 A/B signalsInterpretation of transmitted MFC signals Brazil Config 1 R2 A/B signals Brazil ConfigInterpretation of received MFC signals Brazil Config Brazil Config 2 R2 A/B signals Argentina Config Argentina Config 1 R2 A/B Signals Interpretation of received MFC signals Chile Config 1 R2 A/B signals Chile ConfigSignal Block Panama Config Configuring DIP switch settings and definitions NN40010-300 Diagnostics and Loopback Dip Switch Settings Appendix B Diagnostic and loopback DIP switch settingsDiagnostic and loopback DIP switch settings NN40010-300 MFC signal meaning Appendix C MFC Signal DefinitionsMFC signal definitions MFC Signal Definitions NN40010-300 Cable pinouts Appendix D CLI Cable PinoutCLI Cable Pinout NN40010-300
Top Page Image Contents