Transcend Information TS1G-32GCF133 Word 0 General Configuration, Word 3 Default Number of Heads

Page 59

TS1G~32GCF133

133X CompactFlash Card

 

 

 

￿Word 0: General Configuration

This field indicates the general characteristics of the device. When Word 0 of the Identify drive information is 848Ah then the device is a CompactFlash Storage Card and complies with the CFA specification and CFA command set. It is recommended that PCMCIA modes of operation report only the 848Ah value as they are always intended as removable devices.

Bits 15-0: CF Standard Configuration Value

Word 0 is 848Ah. This is the recommended value of Word 0.

Some operating systems require Bit 6 of Word 0 to be set to 1 (Non-removable device) to use the card as the root storage device. The Card must be the root storage device when a host completely replaces conventional disk storage with a CompactFlash Card in True IDE mode. To support this requirement and provide capability for any future removable media Cards, alternatehandling of Word 0 is permitted.

Bits 15-0: CF Preferred Alternate Configuration Values

044Ah: This is the alternate value of Word 0 turns on ATA device and turns off Removable Media and Removable Device while preserving all Retired bits in the word.

0040h: This is the alternate value of Word 0 turns on ATA device and turns off Removable Media and Removable Device while zeroing all Retired bits in the word

Bit 15-12: Configuration Flag

If bits 15:12 are set to 8h then Word 0 shall be 848Ah.

If bits 15:12 are set to 0h then Bits 11:0 are set using the definitions below and the Card is required to support for the CFA command set and report that in bit 2 of Word 83.

Bit 15:12 values other than 8h and 0h are prohibited.

Bits 11-8: Retired

These bits have retired ATA bit definitions. It is recommended that the value of these bits be either the preferred value of 0h or the value of 4h that preserves the corresponding bits from the 848Ah CF signature value.

Bit 7: Removable Media Device

If Bit 7 is set to 1, the Card contains media that can be removed during Card operation.

If Bit 7 is set to 0, the Card contains nonremovable media.

Bit 6: Not Removable Controller and/or Device

Alert! This bit will be considered for obsolescence in a future revision of this standard. If Bit 6 is set to 1, the Card is intended to be nonremovable during operation.

If Bit 6 is set to 0, the Card is intended to be removable during operation.

Bits 5-0: Retired/Reserved

Alert! Bit 2 will be considered for definition in a future revision of this standard and shall be 0 at this time.

Bits 5-1 have retired ATA bit definitions. Bit 2 shall be 0.

Bit 0 is Reserved and shall be 0.

It is recommended that the value of bits 5-0 be either the preferred value of 00h or the value of 0Ah that preserves the corresponding bits from the 848Ah CF signature value.

￿Word 1: Default Number of Cylinders

This field contains the number of translated cylinders in the default translation mode. This value will be the same as the number of cylinders.

￿Word 3: Default Number of Heads

This field contains the number of translated heads in the default translation mode.

￿Word 6: Default Number of Sectors per Track

This field contains the number of sectors per track in the default translation mode.

Transcend Information Inc.

59

Page 58 Page 60
Image 59
Page 58 Page 60
Contents Description Placement FeaturesDimensions Transcend Block Diagram Pin Assignments and Pin Type TS1G~32GCF133 Dir Signal Description133X CompactFlash Card Signal Name Dir Pin Description Inpack Iowr VCC Wait TS1G~32GCF133 Electrical SpecificationOutput Drive Type Output Drive Characteristics Signal Interface Pull-up pin 45 BVD2 to avoid sensing their batteries as Low TS1G~32GCF133133X CompactFlash CardTable Typical Series Termination for Ultra DMA Ultra DMA Electrical RequirementsSeries termination required for Ultra DMA operation Ultra DMA Mode Cabling Requirement Attribute Memory Read Timing Specification TS1G~32GCF133 Common Memory Read Timing Specification Common Memory Write Timing Specification Input Read Timing Specification TS1G~32GCF133 Output Write Timing Specification TS1G~32GCF133 True IDE PIO Mode Read/Write Timing Specification TS1G~32GCF133 Table Ultra DMA Data Burst Timing True IDE Ultra DMA Mode Read/Write Timing SpecificationTS1G~32GCF133 TS1G~32GCF133 TS1G~32GCF133 TS1G~32GCF133 Multiple Function CompactFlash Storage Cards Card ConfigurationAttribute Memory Function Attribute Memory FunctionConfiguration Option Register Base + 00h in Attribute Memory TS1G~32GCF133 Pin Replacement Register Base + 04h in Attribute Memory Socket and Copy Register Base + 06h in Attribute Memory Transfer Function Table Pcmcia Mode I/O FunctionTable Common Memory Function Common Memory Transfer FunctionTrue IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Table Primary and Secondary I/O Decoding Primary and Secondary Address ConfigurationsTable Contiguous I/O Decoding Contiguous I/O Mapped AddressingMemory Mapped Addressing True IDE Mode AddressingData Register Address 1F0h170hOffset 0,8,9 CF-ATA RegistersCylinder Low LBA 15-8 Register Address 1F4h174h Offset Feature Register Address 1F1h171h Offset 1, 0Dh Write OnlySector Count Register Address 1F2h172h Offset Sector Number LBA 7-0 Register Address 1F3h173h OffsetTS1G~32GCF133 Device Control Register Address 3F6h376h Offset Eh Card Drive Address Register Address 3F7h377h Offset Fh LBA CF-ATA Command SetDefinitions Check Power Mode 98h or E5h Erase Sectors C0h Execute Drive Diagnostic 90hFormat Track 50h Flush Cache E7hIdentify Device Ech Word Default Total Data Field Type InformationTotal Data Field Type Information Word 6 Default Number of Sectors per Track Word 0 General ConfigurationWord 1 Default Number of Cylinders Word 3 Default Number of HeadsWords 10-19 Serial Number Word 49 Capabilities Bit 13 Standby TimerPIO Data Transfer Cycle Timing Mode Words 7-8 Number of Sectors per CardWord 64 Advanced PIO transfer modes supported Multiple Sector SettingTotal Sectors Addressable in LBA Mode Multiword DMA transferWord 68 Minimum PIO transfer cycle time with Iordy Words 82-84 Features/command sets supportedWord 88 Ultra DMA Modes Supported and Selected Words 85-87 Features/command sets enabledWord 128 Security Status Bit 8 Security Level Word 91 Advanced power management level valueWord 160 Power Requirement Description Word 89 Time required for Security erase unit completionValue Value Maximum PIO mode timing selectedAdditional Requirements for CF Advanced Timing Modes Idle 97h or E3h Value Maximum Pcmcia IO timing mode SupportedValue Maximum Memory timing mode Supported NOP 00h Idle Immediate 95h or E1hInitialize Drive Parameters 91h Read DMA C8h Read Long Sector 22h or 23h Read Buffer E4hTS1G~32GCF133 Seek 7Xh Set Features EFh Feature Supported TS1G~32GCF133 Translate Sector Information Standby Immediate 94h or E0h Translate Sector 87hWear Level F5h Write Buffer E8h Write DMA CAh TS1G~32GCF133 TS1G~32GCF133 Error Posting Smart Command Set Smart Feature Register Values Smart Command SetDecription Smart Data Structure

TS1G-32GCF133 specifications

Transcend Information, a leading manufacturer of storage and multimedia products, offers a range of high-performance memory solutions. One prominent product is the TS1G-32GCF133, a compact and reliable CompactFlash (CF) card designed for various applications, from professional photography to industrial use and embedded systems.

At the heart of the TS1G-32GCF133 is its 32GB storage capacity, which provides ample space for storing high-resolution images, videos, and data files. This capacity meets the demands of both casual users and professionals requiring significant storage for their content. The card adheres to the CompactFlash Association's CF Type I specifications, ensuring compatibility with a wide range of devices, including DSLRs, camcorders, and even embedded systems.

One of the standout features of this model is its impressive transfer speed. The TS1G-32GCF133 boasts a read speed of up to 133x, which translates to around 20MB/s. This relatively high-speed performance is critical for users who need quick access to data, especially when capturing bursts of images or recording video. The card's write speed, while somewhat lower, ensures that data can still be written effectively without significant delay, making it suitable for various recording scenarios.

Transcend has implemented advanced technologies in the TS1G-32GCF133 to enhance both performance and reliability. The use of SLC (single-level cell) technology in some areas ensures greater endurance and stability, which is particularly important in professional applications where data integrity is paramount. Additionally, the card is equipped with built-in ECC (Error Correction Code) functionality, which detects and corrects potential errors during data transfer, further safeguarding the stored information.

Physical durability is another critical aspect of the TS1G-32GCF133. This CompactFlash card is designed to withstand harsh conditions, making it suitable for use in demanding environments. Its robust construction is resistant to shock, vibration, and extreme temperatures, providing peace of mind for users who need reliable performance in the field or in industrial settings.

In terms of compatibility, the TS1G-32GCF133 supports both the CF5 and CF6 standards, allowing it to work seamlessly with a wide range of devices. The card is also backward compatible with older CF devices, making it a versatile choice for those upgrading their storage solutions.

In conclusion, the Transcend Information TS1G-32GCF133 stands out as a reliable and high-performance CompactFlash card that meets the needs of diverse users. With its substantial storage capacity, impressive transfer speeds, advanced technologies, and robust design, it serves as an ideal solution for professionals and enthusiasts alike who seek performance and reliability in their memory storage.
Top Page Image Contents