Transcend Information TS1G-32GCF133 dimensions Words 85-87 Features/command sets enabled

Page 63

TS1G~32GCF133133X CompactFlash Card

If bit 3 of word 83 is set to one, the CompactFlash Storage Card supports the Advanced Power Management feature set.

Bit 4 of word 83 shall be set to zero; the CompactFlash Storage Card does not support the Removable Media Status feature set.

￿Words 85-87: Features/command sets enabled

Words 85, 86, and 87 shall indicate features/command sets enabled. The value 0000h or FFFFh was placed in each of these words by CompactFlash Storage Cards prior to ATA-4 and shall be interpreted by the host as meaning that features/command sets enabled are not indicated. Bits 1 through 15 of word 86 are reserved. Bits 0-13 of word 87 are reserved. Bit 14 of word 87 shall be set to one and bit 15 of word 87 shall be cleared to zero to provide indication that the features/command sets enabled words are valid. The values in these words should not be depended on by host implementers.

Bit 0 of word 85 shall be set to zero; the SMART feature set is not enabled.

If bit 1 of word 85 is set to one, the Security Mode feature set has been enabled via the Security Set Password command.

Bit 2 of word 85 shall be set to zero; the Removable Media feature set is not supported. Bit 3 of word 85 shall be set to one; the Power Management feature set is supported. Bit 4 of word 85 shall be set to zero; the Packet Command feature set is not enabled.

If bit 5 of word 85 is set to one, write cache is enabled. If bit 6 of word 85 is set to one, look-ahead is enabled.

Bit 7 of word 85 shall be set to zero; release interrupt is not enabled. Bit 8 of word 85 shall be set to zero; Service interrupt is not enabled.

Bit 9 of word 85 shall be set to zero; the Device Reset command is not supported.

Bit 10 of word 85 shall be set to zero; the Host Protected Area feature set is not supported. Bit 11 of word 85 is obsolete.

Bit 12 of word 85 shall be set to one; the CompactFlash Storage Card supports the Write Buffer command. Bit 13 of word 85 shall be set to one; the CompactFlash Storage Card supports the Read Buffer command. Bit 14 of word 85 shall be set to one; the CompactFlash Storage Card supports the NOP command.

Bit 15 of word 85 is obsolete.

Bit 0 of word 86 shall be set to zero; the CompactFlash Storage Card does not support the Download Microcode command.

Bit 1 of word 86 shall be set to zero; the CompactFlash Storage Card does not support the Read DMA Queued and Write DMA Queued commands.

If bit 2 of word 86 shall be set to one, the CompactFlash Storage Card supports the CFA feature set.

If bit 3 of word 86 is set to one, the Advanced Power Management feature set has been enabled via the Set Features command.

Bit 4 of word 86 shall be set to zero; the CompactFlash Storage Card does not support the Removable Media Status feature set.

￿Word 88: Ultra DMA Modes Supported and Selected

Word 88 identifies the Ultra DMA transfer modes supported by the device and indicates the mode that is currently selected. Only one DMA mode shall be selected at any given time. If an Ultra DMA mode is selected, then no Multiword DMA mode shall be selected. If a Multiword DMA mode is selected, then no Ultra DMA mode shall be selected. Support of this word is mandatory if Ultra DMA is supported.

Bits 15-13: Reserved

Bit 12: 1 = Ultra DMA mode 4 is selected 0 = Ultra DMA mode 4 is not selected

Bit 11: 1 = Ultra DMA mode 3 is selected 0 = Ultra DMA mode 3 is not selected

Bit 10: 1 = Ultra DMA mode 2 is selected 0 = Ultra DMA mode 2 is not selected

Bit 9: 1 = Ultra DMA mode 1 is selected 0 = Ultra DMA mode 1 is not selected

Bit 8: 1 = Ultra DMA mode 0 is selected 0 = Ultra DMA mode 0 is not selected

Bits 7-5: Reserved

Bit 4: 1 = Ultra DMA mode 4 and below are supported. Bits 0-3 Shall be set to 1.

Bit 3: 1 = Ultra DMA mode 3 and below are supported, Bits 0-2 Shall be set to 1.

Transcend Information Inc.

63

Page 62 Page 64
Image 63
Page 62 Page 64
Contents Placement Features DimensionsDescription Transcend Block Diagram Pin Assignments and Pin Type TS1G~32GCF133 Signal Description 133X CompactFlash CardDir Signal Name Dir Pin Description Inpack Iowr VCC Wait TS1G~32GCF133 Electrical SpecificationOutput Drive Type Output Drive Characteristics Signal Interface Pull-up pin 45 BVD2 to avoid sensing their batteries as Low TS1G~32GCF133133X CompactFlash CardUltra DMA Electrical Requirements Series termination required for Ultra DMA operationTable Typical Series Termination for Ultra DMA Ultra DMA Mode Cabling Requirement Attribute Memory Read Timing Specification TS1G~32GCF133 Common Memory Read Timing Specification Common Memory Write Timing Specification Input Read Timing Specification TS1G~32GCF133 Output Write Timing Specification TS1G~32GCF133 True IDE PIO Mode Read/Write Timing Specification TS1G~32GCF133 Table Ultra DMA Data Burst Timing True IDE Ultra DMA Mode Read/Write Timing SpecificationTS1G~32GCF133 TS1G~32GCF133 TS1G~32GCF133 TS1G~32GCF133 Multiple Function CompactFlash Storage Cards Card ConfigurationAttribute Memory Function Attribute Memory FunctionConfiguration Option Register Base + 00h in Attribute Memory TS1G~32GCF133 Pin Replacement Register Base + 04h in Attribute Memory Socket and Copy Register Base + 06h in Attribute Memory Transfer Function Table Pcmcia Mode I/O FunctionTable Common Memory Function Common Memory Transfer FunctionTrue IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Table Primary and Secondary I/O Decoding Primary and Secondary Address ConfigurationsTable Contiguous I/O Decoding Contiguous I/O Mapped AddressingMemory Mapped Addressing True IDE Mode AddressingData Register Address 1F0h170hOffset 0,8,9 CF-ATA RegistersCylinder Low LBA 15-8 Register Address 1F4h174h Offset Feature Register Address 1F1h171h Offset 1, 0Dh Write OnlySector Count Register Address 1F2h172h Offset Sector Number LBA 7-0 Register Address 1F3h173h OffsetTS1G~32GCF133 Device Control Register Address 3F6h376h Offset Eh Card Drive Address Register Address 3F7h377h Offset Fh LBA CF-ATA Command SetDefinitions Check Power Mode 98h or E5h Erase Sectors C0h Execute Drive Diagnostic 90hFormat Track 50h Flush Cache E7hIdentify Device Ech Word Default Total Data Field Type InformationTotal Data Field Type Information Word 6 Default Number of Sectors per Track Word 0 General ConfigurationWord 1 Default Number of Cylinders Word 3 Default Number of Heads Words 10-19 Serial Number Word 49 Capabilities Bit 13 Standby Timer PIO Data Transfer Cycle Timing Mode Words 7-8 Number of Sectors per CardWord 64 Advanced PIO transfer modes supported Multiple Sector SettingTotal Sectors Addressable in LBA Mode Multiword DMA transferWord 68 Minimum PIO transfer cycle time with Iordy Words 82-84 Features/command sets supportedWord 88 Ultra DMA Modes Supported and Selected Words 85-87 Features/command sets enabledWord 128 Security Status Bit 8 Security Level Word 91 Advanced power management level valueWord 160 Power Requirement Description Word 89 Time required for Security erase unit completionValue Maximum PIO mode timing selected Additional Requirements for CF Advanced Timing ModesValue Value Maximum Pcmcia IO timing mode Supported Value Maximum Memory timing mode SupportedIdle 97h or E3h Idle Immediate 95h or E1h Initialize Drive Parameters 91hNOP 00h Read DMA C8h Read Long Sector 22h or 23h Read Buffer E4hTS1G~32GCF133 Seek 7Xh Set Features EFh Feature Supported TS1G~32GCF133 Translate Sector Information Standby Immediate 94h or E0h Translate Sector 87hWear Level F5h Write Buffer E8h Write DMA CAh TS1G~32GCF133 TS1G~32GCF133 Error Posting Smart Command Set Smart Feature Register Values Smart Command SetDecription Smart Data Structure
Top Page Image Contents