Command P Pulse Dialing | Western Telematic MT5634 specification

MT5634 Modem; AT Command Set

Command: P	Pulse Dialing
Values:	P, T
Default:	T
Description:	Conﬁgures the modem for pulse (non-touch-tone) dialing. Dialed
	digits are pulsed until a T command or dial modiﬁer is received.

Command: Qn	Result Codes Enable/Disable
Values:	n = 0 or 1
Default:	0
Description:	Q0	Enable result codes.
	Q1	Disable result codes.
	Q2	Returns an OK for backward compatibility with
		some software.

Command: Sr=n	Set Register Value
Values:	r = S-register number; n varies
Default:	None
Description:	Set value of register Sr to value of n, where n is entered in
	decimal format (e.g., S0=1).

Command: Sr?	Read Register Value
Values:	r = S-register number
Default:	None
Description:	Read value of register Sr and display it in 3-digit decimal form
	(e.g., S2? gives the response 043).

Command: T	Tone Dialing
Values:	P, T
Default:	T
Description:	Conﬁgures the modem for DTMF (touch-tone) dialing. Dialed
	digits are tone dialed until a P command or dial modiﬁer
	is received.

Command: Vn	Result Code Format
Values:	n = 0 or 1
Default:	1
Description:	V0	Displays result codes as digits (terse response).
	V1	Displays result codes as words (verbose response).

3-4

Image 12

Western Telematic MT5634 Command P Pulse Dialing, Command Qn Result Codes Enable/Disable, Command Sr=n Set Register Value

Contents

AT Command Set MT5634Page Table of Contents MT5634 Modem AT Command Set Introduction MT5634 Modem AT Command Set AT Command Summary Description Atmtsmodemcr AT Commands Command Ds Dial Command DS=y Dial Stored Telephone NumberCommand En Echo Command Mode Characters Command Fn Echo Online Data Characters Command H n Hook Control Command I n Information RequestCommand M n Monitor Speaker Mode Command N n Modulation Handshake Command P Pulse Dialing Command Qn Result Codes Enable/DisableCommand Sr=n Set Register Value Command Sr? Read Register Value Command Result Code Options Command Result Code SelectionCommand Zn Modem Reset Command Data Carrier Detect DCD Control Command &Dn Data Terminal Ready DTR Control Command &En XON/XOFF Pacing ControlCommand &Fn Load Factory Settings Command &Gn V.22bis Guard Tone Control Command Leased Line Operation Command Pulse Dial Make-to-Break Ratio SelectionCommand &Qn Asynchronous Communications Mode Command Data Set Ready DSR Control Command &Tn Loopback Test V.54 Test Commands Command &V Display Current SettingsCommand &Wn Store Current Conﬁguration Command &Zy=x Store Dialing Command Command \A n Command \B n Transmit BreakCommand \K n Break Control Command \Nn Error Correction Mode Selection Command \Qn Flow Control SelectionCommand \Tn Inactivity Timer Command \Vn Protocol Result Code Command \Xn XON/XOFF Pass-Through Command Data Calling ToneCommand %An Adaptive Answer Result Code Enable Command View Numbers in Blacklist Command %DCn AT Command Control Command Fallback and Fall Forward ControlCommand %Hn Direct Connect Enable Command Cisco Conﬁguration Command $EB n Asynchronous Word Length Command $MB n Online BPS SpeedCommand $RP n Ring Priority vs. AT Command Priority Command $SB n Serial Port Baud Rate Command +VDR=x, y Distinctive Ring Report Command #CBAn Callback AttemptsCommand #CBDn Callback Delay Command #CBF? Callback Failed Attempts Display Command #CBFR Callback Failed Attempts ResetCommand #CBIn Local Callback Inactivity Timer Command #CBNy=x Command #CBSn Callback Enable/Disable Command #Pn Set 11-bit ParityCommand #Sx Enter Setup Password Command #S=x Store Setup Password Register Unit Range Default Description Registers S37 Decimal Registers MT5634 Modem AT Command Set Result Codes Terse Verbose Description Delayed Remote Configuration and Country Code Configuration Example %%%ATMTSMODEM Changing the Setup Password Country Code Configuration MT5634 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free