Example %%%ATMTSMODEM | Western Telematic MT5634 instruction

6.Remote Configuration and Country Code Configuration

6.1. Remote Configuration

Remote conﬁguration is a network management tool that allows you to conﬁgure modems anywhere in your network from one location. With password-protected remote conﬁguration, you can issue AT commands to a remote modem for maintenance or troubleshooting as if you were on-site.

6.1.1.Basic Procedure

The following steps are valid regardless of whether the connection is established by the local or the remote modem.

1.Establish a data connection with a remote modem.

2.Send three remote conﬁguration escape characters followed by AT and the setup password and press [Enter].

•Example: %%%ATMTSMODEM.

•You have four tries to enter the correct password before being disconnected. If the password is correct, the remote modem responds with OK.

3.You can now send AT commands to conﬁgure the remote modem.

4.When you have ﬁnished conﬁguring the remote modem, save the new conﬁguration by typing AT&W0. Press [Enter].

5.Type ATO. Press [Enter] to exit remote conﬁguration. You can now break the connection.

6.1.2.Setup

MT5634 Modems are shipped with a default setup password (MTSMODEM). Because anyone who has the User Guide knows the default setup password, you should change the password and possibly also the remote conﬁguration escape character.

6-1

Image 31

Western Telematic MT5634 manual Remote Configuration and Country Code Configuration, Example %%%ATMTSMODEM

Contents

MT5634 AT Command SetPage Table of Contents MT5634 Modem AT Command Set Introduction MT5634 Modem AT Command Set Description AT Command Summary Atmtsmodemcr AT Commands Command Fn Echo Online Data Characters Command Ds DialCommand DS=y Dial Stored Telephone Number Command En Echo Command Mode Characters Command N n Modulation Handshake Command H n Hook ControlCommand I n Information Request Command M n Monitor Speaker Mode Command Sr? Read Register Value Command P Pulse DialingCommand Qn Result Codes Enable/Disable Command Sr=n Set Register Value Command Data Carrier Detect DCD Control Command Result Code OptionsCommand Result Code Selection Command Zn Modem Reset Command &Gn V.22bis Guard Tone Control Command &Dn Data Terminal Ready DTR ControlCommand &En XON/XOFF Pacing Control Command &Fn Load Factory Settings Command Data Set Ready DSR Control Command Leased Line OperationCommand Pulse Dial Make-to-Break Ratio Selection Command &Qn Asynchronous Communications Mode Command &Zy=x Store Dialing Command Command &Tn Loopback Test V.54 Test CommandsCommand &V Display Current Settings Command &Wn Store Current Conﬁguration Command \B n Transmit Break Command \A nCommand \K n Break Control Command \Vn Protocol Result Code Command \Nn Error Correction Mode SelectionCommand \Qn Flow Control Selection Command \Tn Inactivity Timer Command View Numbers in Blacklist Command \Xn XON/XOFF Pass-ThroughCommand Data Calling Tone Command %An Adaptive Answer Result Code Enable Command Cisco Conﬁguration Command %DCn AT Command ControlCommand Fallback and Fall Forward Control Command %Hn Direct Connect Enable Command $SB n Serial Port Baud Rate Command $EB n Asynchronous Word LengthCommand $MB n Online BPS Speed Command $RP n Ring Priority vs. AT Command Priority Command #CBAn Callback Attempts Command +VDR=x, y Distinctive Ring ReportCommand #CBDn Callback Delay Command #CBNy=x Command #CBF? Callback Failed Attempts DisplayCommand #CBFR Callback Failed Attempts Reset Command #CBIn Local Callback Inactivity Timer Command #S=x Store Setup Password Command #CBSn Callback Enable/DisableCommand #Pn Set 11-bit Parity Command #Sx Enter Setup Password Registers Register Unit Range Default Description S37 Decimal Registers MT5634 Modem AT Command Set Terse Verbose Description Result Codes Delayed Example %%%ATMTSMODEM Remote Configuration and Country Code Configuration Changing the Setup Password Country Code Configuration MT5634 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free