Command %DCn AT Command Control | Western Telematic MT5634 manual

MT5634 Modem; AT Command Set

Command: %DCn AT Command Control

Values:		n = 0 or 1
Default:		0
Description:		%DC0	The modem responds to AT commands.
		%DC1	The modem ignores AT commands.
		Note: The modem will respond to AT%DC for 10 seconds
		after power-up.
Command:	%En	Fallback and Fall Forward Control
Values:		n = 0, 1, or 2
Default:		2
Description:		%E0	Disable fallback and fall forward.
		%E1	Enable fallback, disable fall forward.
		%E2	Enable fallback and fall forward.
Command: %Hn Direct Connect Enable
Values:		n = 0, 1
Default:		0
Description:		%H0	Sets callback security to normal operation.
		%H1	All callback security calls will be direct connect
			regardless of whether the password or phone number
			has the - character.
Command:	%Rn	Cisco Conﬁguration
Values:		n = 0, 1
Default:		0
Description:		%R0	Disables Cisco conﬁguration.
		%R1	Sets E0, Q1, &D0, \N0, $SB9600, and %S1 for
			operation with a Cisco router.
Command: %Sn		Command Speed Response
Values:		n = 0, 1
Default:		0
Description:		%S0	Sets modem to respond to AT commands at all
			normal speeds.
		%S1	AT commands accepted at 115200 bps only.
			Commands at other speeds are ignored.
Command:	$Dn	DTR Dialing
Values:		n = 0 or 1
Default:		0
Description:		$D0	Disables DTR dialing.
		$D1	Dials the number in memory location 0 when
			DTR goes high.

3-12

Image 20

Western Telematic MT5634 manual Command %DCn AT Command Control, Command Fallback and Fall Forward Control

Contents

AT Command Set MT5634Page Table of Contents MT5634 Modem AT Command Set Introduction MT5634 Modem AT Command Set AT Command Summary Description Atmtsmodemcr AT Commands Command Ds Dial Command DS=y Dial Stored Telephone NumberCommand En Echo Command Mode Characters Command Fn Echo Online Data Characters Command H n Hook Control Command I n Information RequestCommand M n Monitor Speaker Mode Command N n Modulation Handshake Command P Pulse Dialing Command Qn Result Codes Enable/DisableCommand Sr=n Set Register Value Command Sr? Read Register Value Command Result Code Options Command Result Code SelectionCommand Zn Modem Reset Command Data Carrier Detect DCD Control Command &Dn Data Terminal Ready DTR Control Command &En XON/XOFF Pacing ControlCommand &Fn Load Factory Settings Command &Gn V.22bis Guard Tone Control Command Leased Line Operation Command Pulse Dial Make-to-Break Ratio SelectionCommand &Qn Asynchronous Communications Mode Command Data Set Ready DSR Control Command &Tn Loopback Test V.54 Test Commands Command &V Display Current SettingsCommand &Wn Store Current Conﬁguration Command &Zy=x Store Dialing Command Command \K n Break Control Command \A nCommand \B n Transmit Break Command \Nn Error Correction Mode Selection Command \Qn Flow Control SelectionCommand \Tn Inactivity Timer Command \Vn Protocol Result Code Command \Xn XON/XOFF Pass-Through Command Data Calling ToneCommand %An Adaptive Answer Result Code Enable Command View Numbers in Blacklist Command %DCn AT Command Control Command Fallback and Fall Forward ControlCommand %Hn Direct Connect Enable Command Cisco Conﬁguration Command $EB n Asynchronous Word Length Command $MB n Online BPS SpeedCommand $RP n Ring Priority vs. AT Command Priority Command $SB n Serial Port Baud Rate Command #CBDn Callback Delay Command +VDR=x, y Distinctive Ring ReportCommand #CBAn Callback Attempts Command #CBF? Callback Failed Attempts Display Command #CBFR Callback Failed Attempts ResetCommand #CBIn Local Callback Inactivity Timer Command #CBNy=x Command #CBSn Callback Enable/Disable Command #Pn Set 11-bit ParityCommand #Sx Enter Setup Password Command #S=x Store Setup Password Register Unit Range Default Description Registers S37 Decimal Registers MT5634 Modem AT Command Set Result Codes Terse Verbose Description Delayed Remote Configuration and Country Code Configuration Example %%%ATMTSMODEM Changing the Setup Password Country Code Configuration MT5634 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free