Command Result Code Options | Western Telematic MT5634 specs

			AT Commands
Command:	Wn	Result Code Options
Values:		n = 0, 1, or 2
Default:		2
Description:		W0	CONNECT result code reports serial port speed, disables
			protocol result codes.
		W1	CONNECT result code reports serial port speed, enables
			protocol result codes.
		W2	CONNECT result code reports line speed, enables
			protocol result codes.
Command:	Xn	Result Code Selection
Values:		n = 0–7
Default:		4
Description:		X0	Basic result codes (CONNECT); does not look for dial
			tone or busy signal.
		X1	Extended result codes (CONNECT 46000 V42bis); does
			not look for dial tone or busy signal.
		X2	Extended result codes with NO DIALTONE; does not
			look for busy signal.
		X3	Extended result codes with BUSY; does not look for
			dial tone.
		X4	Extended result codes with NO DIALTONE and BUSY.
		X5	Extended result codes with NO DIALTONE and BUSY.
		X6	Extended result codes with NO DIALTONE and BUSY.
		X7	Basic result codes with NO DIALTONE and BUSY.
Command: Zn		Modem Reset
Values:		n = 0 or 1
Default:		None	Reset modem to proﬁle saved by the last &W command.
Description:		Z0	Reset modem to proﬁle saved by the last &W command.
		Z1	Same as Z0.
Command:	&Cn	Data Carrier Detect (DCD) Control
Values:		n = 0, 1, 2
Default:		1
Description:		&C0	Forces the DCD circuit to be always ON.
		&C1	DCD goes ON when the remote modem’s carrier signal
			is detected, and goes OFF when the carrier signal is
			not detected.
		&C2	DCD turns OFF upon disconnect for time set by S18. It
			then goes high again (for some PBX phone systems).

3-5

Image 13

Western Telematic MT5634 manual Command Result Code Options, Command Result Code Selection, Command Zn Modem Reset

Contents

MT5634 AT Command SetPage Table of Contents MT5634 Modem AT Command Set Introduction MT5634 Modem AT Command Set Description AT Command Summary Atmtsmodemcr AT Commands Command DS=y Dial Stored Telephone Number Command Ds DialCommand En Echo Command Mode Characters Command Fn Echo Online Data Characters Command I n Information Request Command H n Hook ControlCommand M n Monitor Speaker Mode Command N n Modulation Handshake Command Qn Result Codes Enable/Disable Command P Pulse DialingCommand Sr=n Set Register Value Command Sr? Read Register Value Command Result Code Selection Command Result Code OptionsCommand Zn Modem Reset Command Data Carrier Detect DCD Control Command &En XON/XOFF Pacing Control Command &Dn Data Terminal Ready DTR ControlCommand &Fn Load Factory Settings Command &Gn V.22bis Guard Tone Control Command Pulse Dial Make-to-Break Ratio Selection Command Leased Line OperationCommand &Qn Asynchronous Communications Mode Command Data Set Ready DSR Control Command &V Display Current Settings Command &Tn Loopback Test V.54 Test CommandsCommand &Wn Store Current Conﬁguration Command &Zy=x Store Dialing Command Command \B n Transmit Break Command \A nCommand \K n Break Control Command \Qn Flow Control Selection Command \Nn Error Correction Mode SelectionCommand \Tn Inactivity Timer Command \Vn Protocol Result Code Command Data Calling Tone Command \Xn XON/XOFF Pass-ThroughCommand %An Adaptive Answer Result Code Enable Command View Numbers in Blacklist Command Fallback and Fall Forward Control Command %DCn AT Command ControlCommand %Hn Direct Connect Enable Command Cisco Conﬁguration Command $MB n Online BPS Speed Command $EB n Asynchronous Word LengthCommand $RP n Ring Priority vs. AT Command Priority Command $SB n Serial Port Baud Rate Command #CBAn Callback Attempts Command +VDR=x, y Distinctive Ring ReportCommand #CBDn Callback Delay Command #CBFR Callback Failed Attempts Reset Command #CBF? Callback Failed Attempts DisplayCommand #CBIn Local Callback Inactivity Timer Command #CBNy=x Command #Pn Set 11-bit Parity Command #CBSn Callback Enable/DisableCommand #Sx Enter Setup Password Command #S=x Store Setup Password Registers Register Unit Range Default Description S37 Decimal Registers MT5634 Modem AT Command Set Terse Verbose Description Result Codes Delayed Example %%%ATMTSMODEM Remote Configuration and Country Code Configuration Changing the Setup Password Country Code Configuration MT5634 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free