Command &En XON/XOFF Pacing Control | Western Telematic MT5634

MT5634 Modem; AT Command Set

Command: &Dn Data Terminal Ready (DTR) Control
Values:	n = 0, 1, 2, or 3
Default:	2
Description:	&D0	Modem ignores true status of DTR signal and responds
		as if it is always on.
	&D1	If DTR drops while in online data mode, the modem
		enters command mode, issues an OK, and
		remains connected.
	&D2	If DTR drops while in online data mode, the modem
		hangs up. If the signal is not present, the modem will not
		answer or dial.
	&D3	If DTR drops, modem hangs up and resets as if ATZ
		command were issued.

Command: &En XON/XOFF Pacing Control
Values:	n = 12 or 13
Default:	12
Description:	&E12	Disables XON/XOFF pacing.
	&E13	Enables XON/XOFF pacing.

Command: &Fn	Load Factory Settings
Values:	n = 0
Default:	None
Description:	&F0	Load factory settings as active conﬁguration.
	Note: See also the Z command.
Command: &Gn V.22bis Guard Tone Control
Values:	n = 0, 1, or 2
Default:	0
Description:	&G0	Disable guard tone.
	&G1	Set guard tone to 550 Hz.
	&G2	Set guard tone to 1800 Hz.
	Note: The &G command is not used in North America.
Command: &Kn Flow Control Selection
Values:	n = 0, 3, or 4
Defaults:	3
Description:	&K0	Disable ﬂow control.
	&K3	Enable CTS/RTS hardware ﬂow control.
	&K4	Enable XON/XOFF software ﬂow control.

3-6

Image 14

Western Telematic MT5634 manual Command &Dn Data Terminal Ready DTR Control, Command &En XON/XOFF Pacing Control

Contents

AT Command Set MT5634Page Table of Contents MT5634 Modem AT Command Set Introduction MT5634 Modem AT Command Set AT Command Summary Description Atmtsmodemcr AT Commands Command En Echo Command Mode Characters Command Ds DialCommand DS=y Dial Stored Telephone Number Command Fn Echo Online Data Characters Command M n Monitor Speaker Mode Command H n Hook ControlCommand I n Information Request Command N n Modulation Handshake Command Sr=n Set Register Value Command P Pulse DialingCommand Qn Result Codes Enable/Disable Command Sr? Read Register Value Command Zn Modem Reset Command Result Code OptionsCommand Result Code Selection Command Data Carrier Detect DCD Control Command &Fn Load Factory Settings Command &Dn Data Terminal Ready DTR ControlCommand &En XON/XOFF Pacing Control Command &Gn V.22bis Guard Tone Control Command &Qn Asynchronous Communications Mode Command Leased Line OperationCommand Pulse Dial Make-to-Break Ratio Selection Command Data Set Ready DSR Control Command &Wn Store Current Conﬁguration Command &Tn Loopback Test V.54 Test CommandsCommand &V Display Current Settings Command &Zy=x Store Dialing Command Command \K n Break Control Command \A nCommand \B n Transmit Break Command \Tn Inactivity Timer Command \Nn Error Correction Mode SelectionCommand \Qn Flow Control Selection Command \Vn Protocol Result Code Command %An Adaptive Answer Result Code Enable Command \Xn XON/XOFF Pass-ThroughCommand Data Calling Tone Command View Numbers in Blacklist Command %Hn Direct Connect Enable Command %DCn AT Command ControlCommand Fallback and Fall Forward Control Command Cisco Conﬁguration Command $RP n Ring Priority vs. AT Command Priority Command $EB n Asynchronous Word LengthCommand $MB n Online BPS Speed Command $SB n Serial Port Baud Rate Command #CBDn Callback Delay Command +VDR=x, y Distinctive Ring ReportCommand #CBAn Callback Attempts Command #CBIn Local Callback Inactivity Timer Command #CBF? Callback Failed Attempts DisplayCommand #CBFR Callback Failed Attempts Reset Command #CBNy=x Command #Sx Enter Setup Password Command #CBSn Callback Enable/DisableCommand #Pn Set 11-bit Parity Command #S=x Store Setup Password Register Unit Range Default Description Registers S37 Decimal Registers MT5634 Modem AT Command Set Result Codes Terse Verbose Description Delayed Remote Configuration and Country Code Configuration Example %%%ATMTSMODEM Changing the Setup Password Country Code Configuration MT5634 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free