Command \Qn Flow Control Selection | Western Telematic MT5634

MT5634 Modem; AT Command Set

Command: \Nn	Error Correction Mode Selection
Values:	n = 0–5, or 7
Default:	3
Description:	\N0	Non-error correction mode with data buffering
		(buffer mode; same as &Q6).
	\N1	Direct mode.
	\N2	MNP reliable mode. If the modem cannot make an
		MNP connection, it disconnects.
	\N3	V.42/MNP auto-reliable mode. The modem attempts ﬁrst
		to connect in V.42 error correction mode, then in MNP
		mode, and ﬁnally in non-error correction (buffer) mode
		with continued operation.
	\N4	V.42 reliable mode. If the modem cannot make a V.42
		connection, it disconnects.
	\N5	V.42, MNP, or non-error correction (same as \ N3).
	\N7	V.42, MNP, or non-error correction (same as \ N3).

Command: \Qn	Flow Control Selection
Values:	n = 0, 1, or 3
Default:	3	Disable ﬂow control (same as &K0).
Description:	\Q0	Disable ﬂow control (same as &K0).
	\Q1	XON/XOFF software ﬂow control (same as &K4).
	\Q2	CTS-only ﬂow control. Not supported.
	\Q3	RTS/CTS hardware ﬂow control (same as &K3).

Command: \Tn	Inactivity Timer
Values:	n = 0, 1–255
Default:	0
Description:	Sets the time (in minutes) after the last character is sent or
	received that the modem waits before disconnecting. A value of
	zero disables the timer. Applies only in buffer mode.
	Note: You can also set the inactivity timer by changing the
	value of S30.

Command: \Vn	Protocol Result Code
Values:	n = 0, 1, or 2
Default:	1
Description:	\V0	Disables the appending of the protocol result code to
		the DCE speed.
	\V1	Enables the appending of the protocol result code to
		the DCE speed.
	\V2	Same as \V1.

3-10

Image 18

$Western Telematic MT5634 manual Command \Nn Error Correction Mode Selection, Command \Qn Flow Control Selection$

Contents

AT Command Set MT5634Page Table of Contents MT5634 Modem AT Command Set Introduction MT5634 Modem AT Command Set AT Command Summary Description Atmtsmodemcr AT Commands Command En Echo Command Mode Characters Command Ds DialCommand DS=y Dial Stored Telephone Number Command Fn Echo Online Data Characters Command M n Monitor Speaker Mode Command H n Hook ControlCommand I n Information Request Command N n Modulation Handshake Command Sr=n Set Register Value Command P Pulse DialingCommand Qn Result Codes Enable/Disable Command Sr? Read Register Value Command Zn Modem Reset Command Result Code OptionsCommand Result Code Selection Command Data Carrier Detect DCD Control Command &Fn Load Factory Settings Command &Dn Data Terminal Ready DTR ControlCommand &En XON/XOFF Pacing Control Command &Gn V.22bis Guard Tone Control Command &Qn Asynchronous Communications Mode Command Leased Line OperationCommand Pulse Dial Make-to-Break Ratio Selection Command Data Set Ready DSR Control Command &Wn Store Current Conﬁguration Command &Tn Loopback Test V.54 Test CommandsCommand &V Display Current Settings Command &Zy=x Store Dialing Command Command \A n Command \B n Transmit BreakCommand \K n Break Control Command \Tn Inactivity Timer Command \Nn Error Correction Mode SelectionCommand \Qn Flow Control Selection Command \Vn Protocol Result Code Command %An Adaptive Answer Result Code Enable Command \Xn XON/XOFF Pass-ThroughCommand Data Calling Tone Command View Numbers in Blacklist Command %Hn Direct Connect Enable Command %DCn AT Command ControlCommand Fallback and Fall Forward Control Command Cisco Conﬁguration Command $RP n Ring Priority vs. AT Command Priority Command $EB n Asynchronous Word LengthCommand $MB n Online BPS Speed Command $SB n Serial Port Baud Rate Command +VDR=x, y Distinctive Ring Report Command #CBAn Callback AttemptsCommand #CBDn Callback Delay Command #CBIn Local Callback Inactivity Timer Command #CBF? Callback Failed Attempts DisplayCommand #CBFR Callback Failed Attempts Reset Command #CBNy=x Command #Sx Enter Setup Password Command #CBSn Callback Enable/DisableCommand #Pn Set 11-bit Parity Command #S=x Store Setup Password Register Unit Range Default Description Registers S37 Decimal Registers MT5634 Modem AT Command Set Result Codes Terse Verbose Description Delayed Remote Configuration and Country Code Configuration Example %%%ATMTSMODEM Changing the Setup Password Country Code Configuration MT5634 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free