Command Leased Line Operation | Western Telematic MT5634 manual

			AT Commands
Command:	&Ln	Leased Line Operation
Values:		n = 0, 1, or 2
Defaults:		0
Description:		&L0	The modem is set for standard dial-up operation.
		&L1	The modem is set for leased line operation in
			originate mode.
		&L2	The modem is set for leased line operation in
			answer mode.
		Note: For &L1 and &L2, there is a 30-second window between
		power up and the starting of the leased line handshake. During
		this time, you can turn off the command, if desired.
Command:	&Pn	Pulse Dial Make-to-Break Ratio Selection
Values:		n = 0, 1, or 2
Default:		0
Description:		&P0	60/40 make-to-break ratio
		&P1	67/33 make-to-break ratio
		&P2	20 pulses per second
		Note: The &P2 command is available only if the country code is
		set to Japan.
Command: &Qn Asynchronous Communications Mode
Values:		n = 0, 5, 6, 8, or 9
Default:		5	Asynchronous with data buffering. Same as \N0.
Description:		&Q0	Asynchronous with data buffering. Same as \N0.
		&Q5	Error control with data buffering. Same as \N3.
		&Q6	Asynchronous with data buffering. Same as \N0.
		&Q8	MNP error control mode. If MNP error control is not
			established, the modem falls back according to the
			setting in S36.
		&Q9	V.42 or MNP error control mode. If neither error control
			is established, the modem falls back according to the
			setting in S36.
Command:	&Sn	Data Set Ready (DSR) Control
Values:		n = 0 or 1
Default:		0
Description:		&S0	DSR is always ON.
		&S1	DSR goes ON only during a connection.

3-7

Image 15

Western Telematic MT5634 manual Command Leased Line Operation, Command Pulse Dial Make-to-Break Ratio Selection

Contents

MT5634 AT Command SetPage Table of Contents MT5634 Modem AT Command Set Introduction MT5634 Modem AT Command Set Description AT Command Summary Atmtsmodemcr AT Commands Command Fn Echo Online Data Characters Command Ds DialCommand DS=y Dial Stored Telephone Number Command En Echo Command Mode Characters Command N n Modulation Handshake Command H n Hook ControlCommand I n Information Request Command M n Monitor Speaker Mode Command Sr? Read Register Value Command P Pulse DialingCommand Qn Result Codes Enable/Disable Command Sr=n Set Register Value Command Data Carrier Detect DCD Control Command Result Code OptionsCommand Result Code Selection Command Zn Modem Reset Command &Gn V.22bis Guard Tone Control Command &Dn Data Terminal Ready DTR ControlCommand &En XON/XOFF Pacing Control Command &Fn Load Factory Settings Command Data Set Ready DSR Control Command Leased Line OperationCommand Pulse Dial Make-to-Break Ratio Selection Command &Qn Asynchronous Communications Mode Command &Zy=x Store Dialing Command Command &Tn Loopback Test V.54 Test CommandsCommand &V Display Current Settings Command &Wn Store Current Conﬁguration Command \A n Command \B n Transmit BreakCommand \K n Break Control Command \Vn Protocol Result Code Command \Nn Error Correction Mode SelectionCommand \Qn Flow Control Selection Command \Tn Inactivity Timer Command View Numbers in Blacklist Command \Xn XON/XOFF Pass-ThroughCommand Data Calling Tone Command %An Adaptive Answer Result Code Enable Command Cisco Conﬁguration Command %DCn AT Command ControlCommand Fallback and Fall Forward Control Command %Hn Direct Connect Enable Command $SB n Serial Port Baud Rate Command $EB n Asynchronous Word LengthCommand $MB n Online BPS Speed Command $RP n Ring Priority vs. AT Command Priority Command +VDR=x, y Distinctive Ring Report Command #CBAn Callback AttemptsCommand #CBDn Callback Delay Command #CBNy=x Command #CBF? Callback Failed Attempts DisplayCommand #CBFR Callback Failed Attempts Reset Command #CBIn Local Callback Inactivity Timer Command #S=x Store Setup Password Command #CBSn Callback Enable/DisableCommand #Pn Set 11-bit Parity Command #Sx Enter Setup Password Registers Register Unit Range Default Description S37 Decimal Registers MT5634 Modem AT Command Set Terse Verbose Description Result Codes Delayed Example %%%ATMTSMODEM Remote Configuration and Country Code Configuration Changing the Setup Password Country Code Configuration MT5634 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free