Command #CBSn Callback Enable/Disable | Western Telematic MT5634

MT5634 Modem; AT Command Set

Command:	#CBSn Callback Enable/Disable
Values:	n = 0, 1, 2, or 3
Default:	0
Description:	#CBS0 Disables callback security.
	#CBS1 Enables local and remote callback security.
	#CBS2 Enables remote callback security only.
	#CBS3 Disables callback security until local hang-up or reset.

Command: #Pn	Set 11-bit Parity
Values:	n = 0 or 1
Default:	2
Description:	#P0	No parity.
	#P1	Odd parity.
	#P2	Even parity.

Command: #Sx	Enter Setup Password
Values:	x= password (1–8 characters, case sensitive)
Default:	MTSMODEM
Description:	Enters the remote conﬁguration setup password.

Command: #S=x	Store Setup Password
Values:	x= password (1–8 characters, case sensitive)
Default:	MTSMODEM
Description:	Stores a new remote conﬁguration setup password.

3.1 Escape AT Commands

Command: +++AT<CR>	Escape Sequence
Values:	N/A
Description:	Puts the modem in command mode (and optionally
	issues a command) while remaining online. Type
	+++AT and up to six optional command characters;
	then press [Enter]. Used mostly to issue the hang-up
	command: +++ATH<CR>.
Command: %%%ATMTSMODEM<CR>
	Remote Conﬁguration Escape Sequence
Values:	N/A
Description:	Initiates remote conﬁguration mode while online
	with remote modem. The remote conﬁguration
	escape character (%) is deﬁned in register S13.

3-16

Image 24

Western Telematic MT5634 Command #CBSn Callback Enable/Disable, Command #Pn Set 11-bit Parity, Command %%%ATMTSMODEMCR

Contents

AT Command Set MT5634Page Table of Contents MT5634 Modem AT Command Set Introduction MT5634 Modem AT Command Set AT Command Summary Description Atmtsmodemcr AT Commands Command Ds Dial Command DS=y Dial Stored Telephone NumberCommand En Echo Command Mode Characters Command Fn Echo Online Data Characters Command H n Hook Control Command I n Information RequestCommand M n Monitor Speaker Mode Command N n Modulation Handshake Command P Pulse Dialing Command Qn Result Codes Enable/DisableCommand Sr=n Set Register Value Command Sr? Read Register Value Command Result Code Options Command Result Code SelectionCommand Zn Modem Reset Command Data Carrier Detect DCD Control Command &Dn Data Terminal Ready DTR Control Command &En XON/XOFF Pacing ControlCommand &Fn Load Factory Settings Command &Gn V.22bis Guard Tone Control Command Leased Line Operation Command Pulse Dial Make-to-Break Ratio SelectionCommand &Qn Asynchronous Communications Mode Command Data Set Ready DSR Control Command &Tn Loopback Test V.54 Test Commands Command &V Display Current SettingsCommand &Wn Store Current Conﬁguration Command &Zy=x Store Dialing Command Command \A n Command \B n Transmit BreakCommand \K n Break Control Command \Nn Error Correction Mode Selection Command \Qn Flow Control SelectionCommand \Tn Inactivity Timer Command \Vn Protocol Result Code Command \Xn XON/XOFF Pass-Through Command Data Calling ToneCommand %An Adaptive Answer Result Code Enable Command View Numbers in Blacklist Command %DCn AT Command Control Command Fallback and Fall Forward ControlCommand %Hn Direct Connect Enable Command Cisco Conﬁguration Command $EB n Asynchronous Word Length Command $MB n Online BPS SpeedCommand $RP n Ring Priority vs. AT Command Priority Command $SB n Serial Port Baud Rate Command +VDR=x, y Distinctive Ring Report Command #CBAn Callback AttemptsCommand #CBDn Callback Delay Command #CBF? Callback Failed Attempts Display Command #CBFR Callback Failed Attempts ResetCommand #CBIn Local Callback Inactivity Timer Command #CBNy=x Command #CBSn Callback Enable/Disable Command #Pn Set 11-bit ParityCommand #Sx Enter Setup Password Command #S=x Store Setup Password Register Unit Range Default Description Registers S37 Decimal Registers MT5634 Modem AT Command Set Result Codes Terse Verbose Description Delayed Remote Configuration and Country Code Configuration Example %%%ATMTSMODEM Changing the Setup Password Country Code Configuration MT5634 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free