Registers | Western Telematic MT5634 specification

						S-Registers
Register	Unit	Range	Default	Description

S48	decimal	7 or 128	7	Enables (7) or disables (128) LAPM negotiation.
				The following table lists the S36 and S48
				conﬁguration settings for certain types of connections.
					S48=7	S48=128
				S36=0, 2 LAPM or hang up		Do not use
				S36=1, 3 LAPM or async		Async
				S36=4, 6	LAPM, MNP,	MNP or hang up
					or hang up
				S36=5, 7	LAPM, MNP,	MNP or async
					or async
S89	seconds	0, 5–255	10	Sets the length of time in the off-line command mode
				before the modem goes into standby mode or
				"sleep mode". A value of zero prevents standby
				mode; a value of 1–4 sets the value to 5. Standby
				mode (sleep mode or low power mode) is controlled
				by S89. It programs the number of seconds of
				inactivity before the modem will go to sleep. The
				default value is 0. A value of 0 disables standby
				mode. The modem will wake on an incoming ring
				or an AT command.
S108	decimal	0–3, 6, 7	6	Selects the 56K digital loss if using the modem
				through a PBX line. The default value is -6 dB loss,
				the value used when calling from a typical POTS
				line long distance.
				0 = -0 dB digital loss, no robbed-bit signaling
				1 = -3 dB PBX digital loss
				2 = -2 dB digital loss
				3 = -3 dB digital loss
				6 = -6 dB digital loss
				7 = -0 dB digital loss with robbed-bit signaling

4-3

Image 27

Western Telematic MT5634 manual Registers

Contents

MT5634 AT Command SetPage Table of Contents MT5634 Modem AT Command Set Introduction MT5634 Modem AT Command Set Description AT Command Summary Atmtsmodemcr AT Commands Command Fn Echo Online Data Characters Command Ds DialCommand DS=y Dial Stored Telephone Number Command En Echo Command Mode Characters Command N n Modulation Handshake Command H n Hook ControlCommand I n Information Request Command M n Monitor Speaker Mode Command Sr? Read Register Value Command P Pulse DialingCommand Qn Result Codes Enable/Disable Command Sr=n Set Register Value Command Data Carrier Detect DCD Control Command Result Code OptionsCommand Result Code Selection Command Zn Modem Reset Command &Gn V.22bis Guard Tone Control Command &Dn Data Terminal Ready DTR ControlCommand &En XON/XOFF Pacing Control Command &Fn Load Factory Settings Command Data Set Ready DSR Control Command Leased Line OperationCommand Pulse Dial Make-to-Break Ratio Selection Command &Qn Asynchronous Communications Mode Command &Zy=x Store Dialing Command Command &Tn Loopback Test V.54 Test CommandsCommand &V Display Current Settings Command &Wn Store Current Conﬁguration Command \A n Command \B n Transmit BreakCommand \K n Break Control Command \Vn Protocol Result Code Command \Nn Error Correction Mode SelectionCommand \Qn Flow Control Selection Command \Tn Inactivity Timer Command View Numbers in Blacklist Command \Xn XON/XOFF Pass-ThroughCommand Data Calling Tone Command %An Adaptive Answer Result Code Enable Command Cisco Conﬁguration Command %DCn AT Command ControlCommand Fallback and Fall Forward Control Command %Hn Direct Connect Enable Command $SB n Serial Port Baud Rate Command $EB n Asynchronous Word LengthCommand $MB n Online BPS Speed Command $RP n Ring Priority vs. AT Command Priority Command +VDR=x, y Distinctive Ring Report Command #CBAn Callback AttemptsCommand #CBDn Callback Delay Command #CBNy=x Command #CBF? Callback Failed Attempts DisplayCommand #CBFR Callback Failed Attempts Reset Command #CBIn Local Callback Inactivity Timer Command #S=x Store Setup Password Command #CBSn Callback Enable/DisableCommand #Pn Set 11-bit Parity Command #Sx Enter Setup Password Registers Register Unit Range Default Description S37 Decimal Registers MT5634 Modem AT Command Set Terse Verbose Description Result Codes Delayed Example %%%ATMTSMODEM Remote Configuration and Country Code Configuration Changing the Setup Password Country Code Configuration MT5634 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free