Transcend Information TS1G-32GCF133 dimensions 133X CompactFlash Card, Signal Description, Dir

Page 6

TS1G~32GCF133

 

133X CompactFlash Card

 

 

 

 

 

 

Signal Description

 

 

 

 

 

 

 

 

 

 

Signal Name

Dir.

Pin

Description

 

 

 

 

A10 – A00

I

8,10,11,12,

These address lines along with the -REG signal are used to select the following:

(PC Card Memory Mode)

 

14,15,16,17,

The I/O port address registers within the CompactFlash Storage Card , the

 

 

 

18,19,20

memory mapped port address registers within the CompactFlash Storage Card,

 

 

 

 

a byte in the card's information structure and its configuration control and status

 

 

 

 

registers.

A10 – A00

 

 

This signal is the same as the PC Card Memory Mode signal.

(PC Card I/O Mode)

 

 

 

 

A02 - A00

I

18,19,20

In True IDE Mode, only A[02:00] are used to select the one of eight registers

(True IDE Mode)

 

 

in the Task File, the remaining address lines should be grounded by the

 

 

 

 

host.

 

 

 

 

BVD1

I/O

46

This signal is asserted high, as BVD1 is not supported.

(PC Card Memory Mode)

 

 

 

 

-STSCHG

 

 

This signal is asserted low to alert the host to changes in the READY and Write

(PC Card I/O Mode)

 

 

Protect states, while the I/O interface is configured. Its use is controlled by the

Status Changed

 

 

Card Config and Status Register.

-PDIAG

 

 

In the True IDE Mode, this input / output is the Pass Diagnostic signal in the

(True IDE Mode)

 

 

Master / Slave handshake protocol.

 

 

 

 

BVD2

I/O

45

This signal is asserted high, as BVD2 is not supported.

(PC Card Memory Mode)

 

 

 

 

-SPKR

 

 

This line is the Binary Audio output from the card. If the Card does not support

(PC Card I/O Mode)

 

 

the Binary Audio function, this line should be held negated.

-DASP

 

 

In the True IDE Mode, this input/output is the Disk Active/Slave Present signal in

(True IDE Mode)

 

 

the Master/Slave handshake protocol.

 

 

 

 

-CD1, -CD2

O

26,25

These Card Detect pins are connected to ground on the CompactFlash Storage

(PC Card Memory Mode)

 

 

Card. They are used by the host to determine that the CompactFlash Storage

 

 

 

 

Card is fully inserted into its socket.

-CD1, -CD2

 

 

This signal is the same for all modes.

(PC Card I/O Mode)

 

 

 

 

-CD1, -CD2

 

 

This signal is the same for all modes.

(True IDE Mode)

 

 

 

 

 

 

 

 

 

 

Transcend Information Inc.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Placement Features DimensionsDescription Transcend Block Diagram Pin Assignments and Pin Type TS1G~32GCF133 Signal Description 133X CompactFlash CardDir Signal Name Dir Pin Description Inpack Iowr VCC Wait Electrical Specification TS1G~32GCF133Output Drive Type Output Drive Characteristics Signal Interface TS1G~32GCF133133X CompactFlash Card Pull-up pin 45 BVD2 to avoid sensing their batteries as LowUltra DMA Electrical Requirements Series termination required for Ultra DMA operationTable Typical Series Termination for Ultra DMA Ultra DMA Mode Cabling Requirement Attribute Memory Read Timing Specification TS1G~32GCF133 Common Memory Read Timing Specification Common Memory Write Timing Specification Input Read Timing Specification TS1G~32GCF133 Output Write Timing Specification TS1G~32GCF133 True IDE PIO Mode Read/Write Timing Specification TS1G~32GCF133 True IDE Ultra DMA Mode Read/Write Timing Specification Table Ultra DMA Data Burst TimingTS1G~32GCF133 TS1G~32GCF133 TS1G~32GCF133 TS1G~32GCF133 Card Configuration Multiple Function CompactFlash Storage CardsAttribute Memory Function Attribute Memory FunctionConfiguration Option Register Base + 00h in Attribute Memory TS1G~32GCF133 Pin Replacement Register Base + 04h in Attribute Memory Socket and Copy Register Base + 06h in Attribute Memory Table Pcmcia Mode I/O Function Transfer FunctionCommon Memory Transfer Function Table Common Memory FunctionTrue IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Primary and Secondary Address Configurations Table Primary and Secondary I/O DecodingContiguous I/O Mapped Addressing Table Contiguous I/O DecodingTrue IDE Mode Addressing Memory Mapped AddressingCF-ATA Registers Data Register Address 1F0h170hOffset 0,8,9Sector Number LBA 7-0 Register Address 1F3h173h Offset Feature Register Address 1F1h171h Offset 1, 0Dh Write OnlySector Count Register Address 1F2h172h Offset Cylinder Low LBA 15-8 Register Address 1F4h174h OffsetTS1G~32GCF133 Device Control Register Address 3F6h376h Offset Eh Card Drive Address Register Address 3F7h377h Offset Fh CF-ATA Command Set LBADefinitions Check Power Mode 98h or E5h Execute Drive Diagnostic 90h Erase Sectors C0hFlush Cache E7h Format Track 50hWord Default Total Data Field Type Information Identify Device EchTotal Data Field Type Information Word 3 Default Number of Heads Word 0 General ConfigurationWord 1 Default Number of Cylinders Word 6 Default Number of Sectors per TrackWords 7-8 Number of Sectors per Card Word 49 Capabilities Bit 13 Standby TimerPIO Data Transfer Cycle Timing Mode Words 10-19 Serial NumberMultiword DMA transfer Multiple Sector SettingTotal Sectors Addressable in LBA Mode Word 64 Advanced PIO transfer modes supportedWords 82-84 Features/command sets supported Word 68 Minimum PIO transfer cycle time with IordyWords 85-87 Features/command sets enabled Word 88 Ultra DMA Modes Supported and SelectedWord 89 Time required for Security erase unit completion Word 91 Advanced power management level valueWord 160 Power Requirement Description Word 128 Security Status Bit 8 Security LevelValue Maximum PIO mode timing selected Additional Requirements for CF Advanced Timing ModesValue Value Maximum Pcmcia IO timing mode Supported Value Maximum Memory timing mode SupportedIdle 97h or E3h Idle Immediate 95h or E1h Initialize Drive Parameters 91hNOP 00h Read Buffer E4h Read DMA C8h Read Long Sector 22h or 23hTS1G~32GCF133 Seek 7Xh Set Features EFh Feature Supported TS1G~32GCF133 Standby Immediate 94h or E0h Translate Sector 87h Translate Sector InformationWear Level F5h Write Buffer E8h Write DMA CAh TS1G~32GCF133 TS1G~32GCF133 Error Posting Smart Command Set Smart Command Set Smart Feature Register ValuesSmart Data Structure Decription

TS1G-32GCF133 specifications

Transcend Information, a leading manufacturer of storage and multimedia products, offers a range of high-performance memory solutions. One prominent product is the TS1G-32GCF133, a compact and reliable CompactFlash (CF) card designed for various applications, from professional photography to industrial use and embedded systems.

At the heart of the TS1G-32GCF133 is its 32GB storage capacity, which provides ample space for storing high-resolution images, videos, and data files. This capacity meets the demands of both casual users and professionals requiring significant storage for their content. The card adheres to the CompactFlash Association's CF Type I specifications, ensuring compatibility with a wide range of devices, including DSLRs, camcorders, and even embedded systems.

One of the standout features of this model is its impressive transfer speed. The TS1G-32GCF133 boasts a read speed of up to 133x, which translates to around 20MB/s. This relatively high-speed performance is critical for users who need quick access to data, especially when capturing bursts of images or recording video. The card's write speed, while somewhat lower, ensures that data can still be written effectively without significant delay, making it suitable for various recording scenarios.

Transcend has implemented advanced technologies in the TS1G-32GCF133 to enhance both performance and reliability. The use of SLC (single-level cell) technology in some areas ensures greater endurance and stability, which is particularly important in professional applications where data integrity is paramount. Additionally, the card is equipped with built-in ECC (Error Correction Code) functionality, which detects and corrects potential errors during data transfer, further safeguarding the stored information.

Physical durability is another critical aspect of the TS1G-32GCF133. This CompactFlash card is designed to withstand harsh conditions, making it suitable for use in demanding environments. Its robust construction is resistant to shock, vibration, and extreme temperatures, providing peace of mind for users who need reliable performance in the field or in industrial settings.

In terms of compatibility, the TS1G-32GCF133 supports both the CF5 and CF6 standards, allowing it to work seamlessly with a wide range of devices. The card is also backward compatible with older CF devices, making it a versatile choice for those upgrading their storage solutions.

In conclusion, the Transcend Information TS1G-32GCF133 stands out as a reliable and high-performance CompactFlash card that meets the needs of diverse users. With its substantial storage capacity, impressive transfer speeds, advanced technologies, and robust design, it serves as an ideal solution for professionals and enthusiasts alike who seek performance and reliability in their memory storage.
Top Page Image Contents