Agilent Technologies 6634B, 66332A, 6633B, 6632B SOURceVOLTageALCBANDwidth? SOURceVOLTageALCBWIDth?

Page 60

4 - Language Dictionary

[SOURce:]VOLTage:ALC:BANDwidth?

[SOURce:]VOLTage:ALC:BWIDth?

Agilent 66332A, 6631B, 6632B, 6633B and 6634B Only

These queries return the setting of the output mode switch. The output mode switch is used to connect or disconnect the the output capacitor located inside the unit. The returned value is 15,000 if the switch is set to Normal and 60,000 if the switch is set to Fast.

Query Syntax [SOURce]:VOLTage:ALC:BANDwidth? [SOURce]:VOLTage:ALC:BWIDth?

Examples VOLT:ALC:BAND? VOLTAGE:ALC:BWIDth?

Returned Parameters <NR3>

[SOURce:]VOLTage:TRIGger

This command sets the pending triggered voltage level of the dc source. The pending triggered level is a stored voltage value that is transferred to the output terminals when a trigger occurs. In order for a trigger to occur, the trigger subsystem must be initiated (see the INITiate command in the trigger subsystem).

Command Syntax

[SOURce][:VOLTage[:LEVel]:TRIGgered[:AMPLitude]<NRf+>

Parameters

see Table 4-3

 

Default Suffix

V (volts)

 

*RST Value

0

 

Examples

VOLT:TRIG 20

VOLTAGE:LEVEL:TRIGGERED 20

Query Syntax

[SOURce]:VOLTage[LEVel]:TRIGgered[:AMPLitude]?

Returned Parameters

<NR3>

 

Related Commands

VOLT *RST

 

[SOURce:]VOLTage:PROTection

This command sets the overvoltage protection (OVP) level of the dc source. If the output voltage exceeds the OVP level, then the dc source output is disabled and the Questionable Condition status register OV bit is set (see chapter 3 under Programming the Status Registers). An overvoltage condition can be cleared with the OUTP:PROT:CLE command after the condition that caused the OVP trip is removed. The OVP always trips with zero delay and is unaffected by the OUTP:PROT:DEL command.

Command Syntax

[SOURce]:VOLTage:PROTection[:LEVel]<NRf+>

Parameters

see Table 4-3

 

Default Suffix

V (volts)

 

*RST Value

MAX

 

Examples

VOLT:PROT 21.5

VOLT:PROT:LEV MAX

Query Syntax

[SOURce]:VOLTage:PROTection[:LEVel]?

Returned Parameters

<NR3>

 

Related Commands

OUTP:PROT:CLE

OUTP:PROT:DEL

60

Image 60
Contents Programming Guide Safety Guidelines Printing HistoryTable of Contents Language Dictionary Internally Triggered MeasurementsOutput Commands Error Messages Scpi Conformance InformationCompatibility Language Example ProgramsAbout this Guide Documentation SummaryExternal References Gpib ReferencesScpi References VXIplug&play Power Products Instrument Drivers Downloading and Installing the DriverSupported Applications System RequirementsAccessing Online Help Gpib Capabilities of the DC SourceRS-232 Capabilities of the DC Source Gpib AddressRS-232 Flow Control RS-232 Programming ExampleBaud Rate RS-232 Troubleshooting Introduction to ScpiConventions Used in This Guide Boldface fontTypes of Scpi Commands Multiple Commands in a MessageIncluding Common Commands Using QueriesTypes of Scpi Messages Moving Among SubsystemsQuery Indicator Message UnitHeaders Message Unit SeparatorScpi Data Formats Numerical Data FormatsSuffixes and Multipliers Response Data TypesScpi Command Completion Using Device ClearPage Power-on Initialization IntroductionProgramming the Output Enabling the OutputOutput Voltage Output CurrentMaximum Voltage Maximum CurrentSetting the Voltage or Current Trigger Levels Triggering Output ChangesScpi Triggering Nomenclature Output Trigger System ModelInitiating the Output Trigger System Generating TriggersMaking Measurements Voltage and Current MeasurementsDC Measurements RMS Measurements Agilent 66312A, 66332A Only Current RangesInternally Triggered Measurements Measurement Trigger System ModelSequence Form Alias SEQuence2 ACQuire Generating Measurement Triggers Agilent 66312A, 66332A Only BUSTrigger Commands Used to Measure Output Pulses Measuring Output Pulses Agilent 66312A, 66332A Only Current DetectorPulse Measurement Queries Controlling Measurement Samples Varying the Voltage or Current Sampling RateMultiple Measurements Agilent 66312A, 66332A Only Pulse Measurement Example Agilent 66312A, 66332A only Pre-event and Post-event TriggeringOption Base Power-On Conditions Programming the Status RegistersOperation Status Group Questionable Status Group Standard Event Status GroupStatus Byte Register Determining the Cause of a Service Interrupt Servicing Operation Status and Questionable Status EventsMSS Bit RQS BitInhibit/Fault Indicator Monitoring Both Phases of a Status TransitionDiscrete Fault Indicator DFI Remote Inhibit RIUsing the Inhibit/Fault Port as a Digital I/O Bit WeightDFI Programming Example PinPage Subsystem Commands Language DictionarySubsystem Commands Syntax DFI ALCSubsystem Commands Syntax Common Commands Common Commands SyntaxProgramming Parameters Output Programming ParametersCalibration Commands CALibrateCURRentCALibrateCURRentNEGative CALibrateCURRentMEASureLOWRangeCALibratePASSword Command Syntax CALibrateSAVE Parameters None ExamplesCALibrateDATA CALibrateLEVelCALibrateSTATe CALibrateVOLTageCALibrateVOLTagePROTection Query Syntax CALibrateSTATe?Measurement Commands MEASureARRayCURRent? FETChARRayCURRent?MEASureARRayVOLTage? FETChARRayVOLTage? Query SyntaxMEASureCURRent? FETChCURRent? MEASureCURRentACDC? FETChCURRentACDC?MEASureCURRentHIGH? FETChCURRentHIGH? FETChCURRent? applies to Agilent 66312A, 66332A OnlyMEASureCURRentLOW? FETChCURRentLOW? MEASureCURRentMAXimum? FETChCURRent MAXimum?MEASureCURRentMINimum? FETChCURRentMINimum? MEASureVOLTage? FETChVOLTage? MEASureVOLTageACDC? FETChVOLTageACDC?MEASureVOLTageHIGH? FETChVOLTageHIGH? FETChVOLTage? applies to Agilent 66312A, 66332A OnlyMEASureVOLTageLOW? FETChVOLTageLOW? MEASureVOLTageMAXimum? FETChVOLTageMAXimum?MEASureVOLTageMINimum? FETChVOLTageMINimum? SENSeCURRentRANGe SENSeCURRentDETectorUnit a amperes *RST Value MAX high range Returned Parameters NR3SENSeFUNCtion SENSeSWEepOFFSetPOINtsSENSeSWEepPOINts SENSeSWEepTINTervalSENSeWINDow HANNingRECTangular Returned Parameters CRDOutput Commands OUTPutOUTPutDFI OUTPutDFISOURceOUTPutPROTectionDELay OUTPutPONSTATeOUTPutPROTectionCLEar OUTPutRELay OUTPutRELayPOLarityOUTPutRIMODE Query Syntax OUTPputRELayPOLarity?Default Suffix SOURceCURRentSOURceCURRentTRIGger SOURceCURRentPROTectionSTATeSOURceDIGitalDATA SOURceDIGitalFUNCtionSOURceVOLTage Query Syntax SOURceDIGitalDATA?SOURceVOLTageALCBANDwidth? SOURceVOLTageALCBWIDth? SOURceVOLTageTRIGgerSOURceVOLTagePROTection Agilent 66332A, 6631B, 6632B, 6633B and 6634B OnlyStatus Commands STATusPRESetSTATusOPERation? STATusOPERationCONDition?STATusOPERationENABle Query Syntax STATusOPERationENABle?Parameters Preset Value STATusOPERationNTR STATusOPERationPTRSTATusQUEStionableENABle STATusQUEStionable?STATusQUEStionableCONDition? Command Syntax *CLS Parameters None STATusQUEStionableNTR STATusQUEStionablePTRCLS STATQUESNTR?STATQUESPTR?Bit Configuration of Standard Event Status Enable Register ESEESR? OPCPSC SREPSC on ExampleBit Configuration of Status Byte Register STB?WAI NR1 register binary valueSystem Commands DISPlayDISPlayMODE DISPlayTEXTSYSTemERRor? SYSTemLANGuageSYSTemVERSion? Parameters none Returned Parameters NR2SYSTemLOCal SYSTemREMoteSYSTemRWLock IDN?Command Syntax RCL NRf Parameters Example OPT?RCL RSTRST Settings Command Syntax SAV NRf Parameters ExampleSAV TST?Trigger Commands ABORtINITiateSEQuence INITiateNAME INITiateCONTinuousSEQuence1 INITiateCONTinuousNAMETRIGger TRIGgerSOURceTRIGgerSEQuence2 TRIGgerACQuire Abor Currtrig Init *TRG VolttrigTRIGgerSEQuence2COUNtCURRent TRIGgerACQuireCOUNtCURRent TRIGgerSEQuence2COUNtVOLTage TRIGgerACQuireCOUNtVOLTageParameters RST Value Examples TRIGSEQ2COUNCURR 5 TrigacqcouncurrTRIGSEQ2HYSTVOLT TRIGSEQ2LEVCURR TRIGSEQ2HYSTCURR TRIGSEQ2LEVVOLTTRIGgerSEQuence2LEVelCURRent TRIGgerACQuireLEVelCURRent TRIGgerSEQuence2LEVelVOLTage TRIGgerACQuireLEVelVOLTageTRIGSEQ2LEVVOLT TRIGSEQ2HYSTCURR TRIGSEQ2LEVCURR TRIGSEQ2HYSTVOLTTRIGgerSEQuence2SLOPeCURRent TRIGgerACQuireSLOPeCURRent TRIGgerSEQuence2SLOPeVOLTage TRIGgerACQuireSLOPeVOLTageTRIGSEQ2SLOPVOLT Parameters None Related Commands TRIGgerSEQuence2SOURce TRIGgerACQuireSOURceTRIGgerSEQuence1DEFine TRIGgerSEQuence2DEFine TRGPage Scpi Confirmed Commands Non-SCPI CommandsScpi Version Page Table B-1. COMPatibility Power-on Settings Command Command SettingTable B-2. COMPatibility Commands Compatibility ERR? FAULT? ID? IOUT?Similar Scpi Command ASTS? CLRCompatibility Command Table B-2. COMPatibility Commands Description Similar ScpiTable B-2. COMPatibility Commands Compatibility Description CommandThese commands determine the conditions that will set bits ErrorNorm Fast INH ERR UNR +CC RQS ERR RDYFAU Page Error Number List Bit Set Error Number Error Code Error TypeTable C-1. Error Numbers Error Number Page Assigning the Gpib Address in Programs Types of DOS DriversAgilent 82335A Driver National Instruments Gpib DriverError Handling Basic ControllersExample Programs D Example 2. IBM Controller Using National Interface Call IBCLRPS%CODES$=*CLS Example 3. Controller Using Basic Option BaseIndex Index 100101 Scpi102 Manual Updates
Related manuals
Manual 82 pages 25.5 Kb Manual 83 pages 60.43 Kb

6613C, 66312A, 6631B, 6611C, 6614C specifications

Agilent Technologies, a leader in electronic test and measurement solutions, offers a range of power supplies designed to meet various application needs. Notable models include the 6632B, 6634B, 66332A, 6633B, and 6612C. Each of these units provides unique features and technologies that cater to researchers, engineers, and technicians in the industry.

The Agilent 6632B is a single-output DC power supply that delivers up to 30V and 3A. It is known for its excellent load regulation and low noise, making it ideal for sensitive electronic testing. The model includes built-in voltage and current measurement capabilities, allowing users to monitor output conditions in real time. The 6632B is commonly used in laboratory environments, educational institutions, and manufacturing lines.

Moving to the 6634B, this model offers dual-output capabilities with a maximum output of 30V and 6A. This versatility enables simultaneous powering of two different devices or circuit sections. It also features parallel and series operation options, allowing users to create a custom power supply configuration for specific applications. With a programmable interface, the 6634B simplifies test automation, ensuring efficiency in extensive testing scenarios.

The Agilent 66332A stands out with its precision and high performance. This power supply provides three outputs—two programmable and one fixed—yielding flexible power configurations. Its intuitive user interface allows easy adjustment of voltage and current settings. The device is equipped with extensive protection features to safeguard both the power supply and the connected load against faults. It is an excellent choice for complex testing setups that require reliable power.

The 6633B model offers a high-performance power supply with dual outputs, similar to the 6634B but with enhanced specifications. It can provide up to 40V and 2A per channel, delivering precision for demanding applications. This model is particularly suited for industries focused on high-reliability applications, such as telecommunications and aerospace.

Lastly, the Agilent 6612C is a compact and lightweight power supply providing single-output up to 60V and 2A. This model is designed for simplicity and ease of use, making it an excellent choice for portable applications. The 6612C’s unique characteristics include a compact design and user-friendly controls, which facilitate operation in field settings.

In summary, Agilent Technologies’ power supply models—6632B, 6634B, 66332A, 6633B, and 6612C—offer an array of features that cater to a wide range of testing and research needs, ensuring reliable power delivery in various contexts.