AMT Datasouth 4000 manual Connecting the Power Cord, Power Cord Connection

Page 13

Connecting the Power Cord

1.Ensure printer Power Switch is off "0".

2.IMPORTANT: (FM4402 ONLY) Ensure the AC Voltage Select Switch is set to the correct Voltage for this installation.

3.Remove the yellow voltage setting label from the AC Inlet Receptacle .

4.Connect the power cord to the AC Inlet Receptacle located on the back of the printer.

5.Connect AC power plug to a suitable AC source.

6.Connect either Centronics Parallel cable or RS-232 Cable.

CAUTION (FM4402 ONLY): Failure to properly set the AC Voltage Select Switch will cause damage to the printer and will Void the warranty. Ensure this is set properly before connecting the AC power cord.

AC Voltage Select Switch

(FM4402 ONLY)

Power Switch

AC Inlet Receptacle

Figure 7 - Power Cord Connection

12 User's Guide

Image 13

Contents User’s Guide Important Safety Instructions Other Notices Technical Support Table of Contents Reader Table of Figures This page is blank Product Description Overview Unpacking and Inspection Setting up the Printer Installation and ConfigurationFM 4402 Back Panel Power Cord Connection Connecting the Power CordCommunication Cable Connecting the Printer to Your HostFactory default parameters of serial port are Thermal Transfer Media only Loading the RibbonPrinthead Latch and Side Access Cover Ribbon Routing Users Guide Loading Media Fully open Media Access CoverPrinthead Latch and Side Access Cover Outside Media Guide Media Sensor Adjust Knob Media Routing To change the position of the Media Spindle Changing Position of the Media Supply SpindleCalibrating Media Sensors Performing the Self Test Self Test FM4602/FM4603 Ppla Self Test Pattern for FM4602/FM4603 PplaSelf Test FM6402/FM4603 Pplb Self Test Pattern for FM4602/FM4603 PplbSelf Test FM4402 Ppla Self Test Pattern for FM4402 PplaSelf Test FM4402 Pplb Self Test Pattern for FM4402 PplbResetting the Printer to Factory Default Settings This is a blank Front Panel Panel OperationReady Media Ribbon LED IndicatorsButton Function ButtonsButton Function Pause Enter into the printers Setup menu LCD Display FM4602 and 4603 models only With Keyboard Option installedStandard Printer Abnormal Conditions With Barcode Reader OptionFront Panel Set-up Menu LCD and Button functionality in Set-up modeFM 4602 and FM 4603 models only Procedure to Enter into Set-up ModeRange Factory Default Remarks Set-up Mode Selection ItemsUsers Guide Range Factory Default Setting Display LanguageBack Panel FM 4602/4603 Standard Switch Settings Back Panel Switches FM4602 and FM4603 models onlySwitch number Special Condition Special Switch SettingsPS/2 Keyboard I/F FM4602 and FM4603 models only System Setting Commands Command Set for PplaCommand Description Parameter Factory default Symbol Code hexadecimal Interaction CommandsCommand Description Remarks System Level CommandsCommand Description Formatting CommandsCommand structure Command function Editing CommandsComponents Description Variables Command Baaabbbcccddd Object Command Structure DescriptionSuch commands are only used for soft fonts with PCL format Font Downloading CommandsThis is a blank Command Description Parameter Command Set for PplbLEx,y,hlen,vlen D1,hadj This is a blank Printer Driver \WIN95 A\NT40 \WIN98 A\WIN2000 Driver InstallationParameter setting How to Use the DriverDetails Tab Print to the following port Orientation Media choice Device Options This is a blank Possible Problems Solutions Remarks TroubleshootingReady and Media LEDs blinking Ready and Ribbon LED BlinkingOnly the Ready LED blinks LCD display Possible Problems and Solutions RemarksHost indicates Printer Time Out Data has been sent, but there is no output from the printer RecoveryUnstable ribbon roll rotation Poor printout qualityCleaning the Printhead TPH Preventive MaintenanceCleaning the media compartment Cleaning the Platen rollerThis is a blank Specification Model FM4402 Model FM4602 Model FM4603 General SpecificationsFonts, Bar Codes and Graphics Specification Model FM4402, FM4602 and FM4603Printer Programming Language A, Ppla Printer Programming Language B, PplbOptional Accessories This is a blank Serial IntroductionConnection with host Serial port settings Auto Polling Parallel CentronicsAppendix C Printer Status Appendix D Ascii Table Internal Fonts Appendix E Fonts and BAR Codes for PplaUsers Guide Users Guide Font Users Guide Courier Font Set Users Guide Users Guide Users Guide Internal Bar Codes Users Guide Users Guide Users Guide This is a blank Appendix F Fonts and BAR Codes for Pplb Users Guide Users Guide Users Guide Internal Bar Codes Users Guide Key Function KeyboardReady 203,PPLB ESC for Keybd Label SET NO. ? Copies PER LAB ? 0123456789Output Fsreader Barcode Reader11223344 AppleUsers Guide This is a blank AMT Datasouth Corp