AMT Datasouth 4000 manual Changing Position of the Media Supply Spindle

Page 25

Changing Position of the Media Supply Spindle

The printer can store under the Media Access Cover an 8-inch outer diameter media roll that is wound on either 1.5 inch or 3 inch inner cores. When the Media Access Cover is closed touching on either the Media Cover or the bottom of the printer could cause unnecessary drag on the form. The printer's Media Supply Spindle can be moved to accommodate these issues.

To change the position of the Media Spindle:

1.Turn off the printer.

2.Remove the media from the Media Spindle.

3.Using a Phillips Screwdriver remove the 4 screws holding the Media Spindle to the center of the printer.

4.Slide the Media Spindle to the appropriate position.

1.5 inch inner core:	Media Spindle needs to be in the Lower position.
3-inch inner core:	Media Spindle needs to be in the Upper Position.

5.Using a Phillips Screwdriver, install the 4 removed screws.

6.Reload the Media into the printer.

Upper Position

Lower Position

Figure 18 - Media Spindle Location

24 User's Guide

Image 25

Contents User’s Guide Important Safety Instructions Other Notices Technical Support Table of Contents Reader Table of Figures This page is blank Product Description Overview Unpacking and Inspection Setting up the Printer Installation and ConfigurationFM 4402 Back Panel Power Cord Connection Connecting the Power CordCommunication Cable Connecting the Printer to Your HostFactory default parameters of serial port are Thermal Transfer Media only Loading the RibbonPrinthead Latch and Side Access Cover Ribbon Routing Users Guide Loading Media Fully open Media Access CoverPrinthead Latch and Side Access Cover Outside Media Guide Media Sensor Adjust Knob Media Routing To change the position of the Media Spindle Changing Position of the Media Supply SpindleCalibrating Media Sensors Performing the Self Test Self Test FM4602/FM4603 Ppla Self Test Pattern for FM4602/FM4603 PplaSelf Test FM6402/FM4603 Pplb Self Test Pattern for FM4602/FM4603 PplbSelf Test FM4402 Ppla Self Test Pattern for FM4402 PplaSelf Test FM4402 Pplb Self Test Pattern for FM4402 PplbResetting the Printer to Factory Default Settings This is a blank Front Panel Panel OperationReady Media Ribbon LED IndicatorsButton Function ButtonsButton Function Pause Enter into the printers Setup menu LCD Display FM4602 and 4603 models only With Keyboard Option installedStandard Printer Abnormal Conditions With Barcode Reader OptionFront Panel Set-up Menu LCD and Button functionality in Set-up modeFM 4602 and FM 4603 models only Procedure to Enter into Set-up ModeRange Factory Default Remarks Set-up Mode Selection ItemsUsers Guide Range Factory Default Setting Display LanguageBack Panel FM 4602/4603 Standard Switch Settings Back Panel Switches FM4602 and FM4603 models onlySwitch number Special Condition Special Switch SettingsPS/2 Keyboard I/F FM4602 and FM4603 models only System Setting Commands Command Set for PplaCommand Description Parameter Factory default Symbol Code hexadecimal Interaction CommandsCommand Description Remarks System Level CommandsCommand Description Formatting CommandsCommand structure Command function Editing CommandsComponents Description Variables Command Baaabbbcccddd Object Command Structure DescriptionSuch commands are only used for soft fonts with PCL format Font Downloading CommandsThis is a blank Command Description Parameter Command Set for PplbLEx,y,hlen,vlen D1,hadj This is a blank Printer Driver \WIN95 A\NT40 \WIN98 A\WIN2000 Driver InstallationParameter setting How to Use the DriverDetails Tab Print to the following port Orientation Media choice Device Options This is a blank Possible Problems Solutions Remarks TroubleshootingReady and Media LEDs blinking Ready and Ribbon LED BlinkingOnly the Ready LED blinks LCD display Possible Problems and Solutions RemarksHost indicates Printer Time Out Data has been sent, but there is no output from the printer RecoveryUnstable ribbon roll rotation Poor printout qualityCleaning the Printhead TPH Preventive MaintenanceCleaning the media compartment Cleaning the Platen rollerThis is a blank Specification Model FM4402 Model FM4602 Model FM4603 General SpecificationsFonts, Bar Codes and Graphics Specification Model FM4402, FM4602 and FM4603Printer Programming Language A, Ppla Printer Programming Language B, PplbOptional Accessories This is a blank Serial IntroductionConnection with host Serial port settings Auto Polling Parallel CentronicsAppendix C Printer Status Appendix D Ascii Table Internal Fonts Appendix E Fonts and BAR Codes for PplaUsers Guide Users Guide Font Users Guide Courier Font Set Users Guide Users Guide Users Guide Internal Bar Codes Users Guide Users Guide Users Guide This is a blank Appendix F Fonts and BAR Codes for Pplb Users Guide Users Guide Users Guide Internal Bar Codes Users Guide Key Function KeyboardReady 203,PPLB ESC for Keybd Label SET NO. ? Copies PER LAB ? 0123456789Output Fsreader Barcode Reader11223344 AppleUsers Guide This is a blank AMT Datasouth Corp