AMT Datasouth 4000 manual Media Sensor Adjust Knob

Page 23

15.Grasping the Sensor Adjust Knob and sliding in or out as needed can move the Media Sensor. This is required only if the sensor must be moved to a specific location on the label to detect a notch (hole) or gap.

Figure 16 - Media Sensor Adjust Knob

16.Important: To ensure proper media feeding and sensor operation, complete the following checklist:

qMedia is wound Face Out (print side out) and feeding off the top of the roll.

qMedia is routed exactly as shown over the Back Media Rail and under the Front Media Rail.

qMedia is routed between the Upper and Lower Media Sensor Arms located under print module.

qThe green Outside Media Guide has been re-installed.

qIf required, the media sensor is adjusted directly over the notch (hole) or gap.

22 User's Guide

Image 23

Contents User’s Guide Important Safety Instructions Other Notices Technical Support Table of Contents Reader Table of Figures This page is blank Product Description Overview Unpacking and Inspection Setting up the Printer Installation and ConfigurationFM 4402 Back Panel Power Cord Connection Connecting the Power CordCommunication Cable Connecting the Printer to Your HostFactory default parameters of serial port are Thermal Transfer Media only Loading the RibbonPrinthead Latch and Side Access Cover Ribbon Routing Users Guide Loading Media Fully open Media Access CoverPrinthead Latch and Side Access Cover Outside Media Guide Media Sensor Adjust Knob Media Routing To change the position of the Media Spindle Changing Position of the Media Supply SpindleCalibrating Media Sensors Performing the Self Test Self Test FM4602/FM4603 Ppla Self Test Pattern for FM4602/FM4603 PplaSelf Test FM6402/FM4603 Pplb Self Test Pattern for FM4602/FM4603 PplbSelf Test FM4402 Ppla Self Test Pattern for FM4402 PplaSelf Test FM4402 Pplb Self Test Pattern for FM4402 PplbResetting the Printer to Factory Default Settings This is a blank Front Panel Panel OperationReady Media Ribbon LED IndicatorsButton Function ButtonsButton Function Pause Enter into the printers Setup menu Standard Printer With Keyboard Option installedLCD Display FM4602 and 4603 models only Abnormal Conditions With Barcode Reader OptionFront Panel Set-up Menu LCD and Button functionality in Set-up modeFM 4602 and FM 4603 models only Procedure to Enter into Set-up ModeRange Factory Default Remarks Set-up Mode Selection ItemsUsers Guide Range Factory Default Setting Display LanguageBack Panel FM 4602/4603 Standard Switch Settings Back Panel Switches FM4602 and FM4603 models onlySwitch number Special Condition Special Switch SettingsPS/2 Keyboard I/F FM4602 and FM4603 models only Command Description Parameter Factory default Command Set for PplaSystem Setting Commands Symbol Code hexadecimal Interaction CommandsCommand Description Remarks System Level CommandsCommand Description Formatting CommandsComponents Description Variables Command Editing CommandsCommand structure Command function Baaabbbcccddd Object Command Structure DescriptionSuch commands are only used for soft fonts with PCL format Font Downloading CommandsThis is a blank Command Description Parameter Command Set for PplbLEx,y,hlen,vlen D1,hadj This is a blank Printer Driver \WIN95 A\NT40 \WIN98 A\WIN2000 Driver InstallationParameter setting How to Use the DriverDetails Tab Print to the following port Orientation Media choice Device Options This is a blank Ready and Ribbon LED Blinking TroubleshootingPossible Problems Solutions Remarks Ready and Media LEDs blinkingHost indicates Printer Time Out LCD display Possible Problems and Solutions RemarksOnly the Ready LED blinks Poor printout quality RecoveryData has been sent, but there is no output from the printer Unstable ribbon roll rotationCleaning the Printhead TPH Preventive MaintenanceCleaning the media compartment Cleaning the Platen rollerThis is a blank Specification Model FM4402 Model FM4602 Model FM4603 General SpecificationsPrinter Programming Language B, Pplb Specification Model FM4402, FM4602 and FM4603Fonts, Bar Codes and Graphics Printer Programming Language A, PplaOptional Accessories This is a blank Serial IntroductionConnection with host Serial port settings Auto Polling Parallel CentronicsAppendix C Printer Status Appendix D Ascii Table Internal Fonts Appendix E Fonts and BAR Codes for PplaUsers Guide Users Guide Font Users Guide Courier Font Set Users Guide Users Guide Users Guide Internal Bar Codes Users Guide Users Guide Users Guide This is a blank Appendix F Fonts and BAR Codes for Pplb Users Guide Users Guide Users Guide Internal Bar Codes Users Guide Key Function KeyboardReady 203,PPLB ESC for Keybd Label SET NO. ? Copies PER LAB ? 0123456789Output Fsreader Barcode Reader11223344 AppleUsers Guide This is a blank AMT Datasouth Corp