Toshiba S20LP instruction manual Parameter and construction, Transfer parameter table

Page 44

6 F 3 B 0 3 5 6

(4)Parameter and construction

	Source parameter			Transfer size and status

A	Bank/CH	Type	B	Transfer size

A+1	Leading address

	Destination parameter

C	Bank/CH	Type

C+1	Leading address

Transfer parameter table

Transfer object				Type	Leading address	Bank/CH	Transfer size	Status flag

		T2N			0 to 127		1 to 128
XW/YW register				00H		0		None
XW/YW register		T3H		00H	0 to 511	0	1 to 256	None
		T3H			0 to 511		1 to 256

W register				01H	0 to 2047	0	1 to 256	None

LW register				02H	0 to 255	0	1 to 256	None

		T2N			0 to 255
RW register				03H		0	1 to 256	None
RW register		T3H		03H	0 to 999	0	1 to 256	None
		T3H			0 to 999

D register				04H	0 to 8191	0	1 to 256	None

		T2N			0 to 1023
F register				03H		0	1 to 256	None
F register		T3H		03H	0 to 32767	0	1 to 256	None
		T3H			0 to 32767

Expanded F register			T	05H	0 to 8191	1 to 15	1 to 256	None
(IC memory card)			3
			3		0 to 65535	1
			H		0 to 65535	1
			H	06H			1 to 256	None
				06H	0 to 57343	2	1 to 256	None
					0 to 57343	2

Expanded F register			T	05H	0 to 8191	1 to 3	1 to 256	None
(T2N internal memory)			2
(T2N internal memory)			N
			N
TOSLINE-S20LP		T2N				1
scan memory				10H	0 to 4095		1 to 256	None
scan memory		T3H		10H	0 to 4095	1 or 2	1 to 256	None
		T3H				1 or 2

EEPROM		T2N			0 to 2047		1 to 256
				20H		0	(Note 1)	None
		T3H		20H	0 to 8191	0		None
		T3H			0 to 8191

(Note 1) When the communication is transfer source (receiving), the transfer size is 1 to 256. When it is destination (transmitting), the transfer size is 1 to 128 for T3H, 1 to 32 for T2N.

⎯ 43 ⎯

Image 44

Contents T2N/T3H stations Important Information Preface Contents System configuration Introduction to S20LPT2N include of S20LP Port Station hardware∙ Overview SN325 SN325For SN325 ∙ Status LEDsS20LP port for T2N PU245N ∙ Station number setting switches ∙ Transmission cable connectors∙ Reset switch only SN325 ∙ Loader portLS overview Menu⎯ 10 ⎯ S20LP-station specifications SpecificationsS20LP system specifications Scan transmission overview Setting the data send block by S-LS Allocation and network assignment by T-PDSSettings on T-PDS Setting for data linkageStation number setting Link PDS screen example Block Send Receive ⎯ 18 ⎯ Global ⎯ 20 ⎯ Settings on S-LS ⎯ 22 ⎯ ⎯ 23 ⎯ ⎯ 24 ⎯ ∙ Scan Access ∙ Start with Standby mode∙ Scan Transmission ∙ Message Transmission∙ Target Scan Time Data linkage example ∙ Settings on T-PDS Setting on S-LS LS setting screen 2 for STN #2 Cable connections RAS function Behavior in trouble∙ Station down ∙ Transmission cable breakageDuring operation Self-diagnostic functionAt initialization at power on T2N LED indicationSN325 RAS information monitored in T2N/T3H Station status Online mapStandby map Loop map Only T2NRAS information monitored on S-LS Number 1-64 on the screen shows the Station numberSelf Station Station No.01 Offline Select the Station Number Click the Status Display Possible error message are as follows Station down informationInstruction Specification Expanded data transfer instructionInstruction format FunctionParameter and construction Transfer parameter tableSample program ∙ OperationRemarks Message transmission Message transmissionComputer link protocol PC link protocol∙ Send Transfer parameters a CMDStatus B TermSTS Status Meaning Detailed Information Send completion status PC link protocol transmission Data write Transfer parametersRID Status See 7.3 5 for details on bits C, D, E, and F Important itemsXW/YW PC link protocol transmission Data read ⎯ 57 ⎯ SW067 Write enabled PC link protocol transmission program RemarksLength END Appendix Scan cycle⎯ 63 ⎯ PDS remote programming PDS Setup options screen