Toshiba S20LP instruction manual Rid

Page 54

6 F 3 B 0 3 5 6

6)Response time limit

Designates a time used to limit the response time from the remote station in 0.1 second units.

F E

0

A+7

0:Use the user-specified value (0.1 to 3276.7 seconds)

1:Use the default value of 30 seconds.

This code indicates the type of register code in which the local or remote station transmission source data is stored. See “T-series Instruction Set (Ladder, SFC)” (UM-TS03***-E004).

RID	Meaning		RID	Meaning
					*1
0000H	XW/YW registers		∗∗05H	F register (0 - 8191)	*1
					*2
0001H	W register		∗∗06H	F register (0 - 65535)	*2
					*3
0002H	LW register		0007H	T register	*3
					*3
0003H	RW register		0008H	C register	*3

0004H	D register		0009H	SW register

*1 Includes the expansion F registers. One bank has 8k words (0 to 8191).

F 7 0

05H

Bank number ... 00H: T2N internal registers

F0000 to F1023

01H to 03H: Expansion F registers

F0000 to F8191

*2 Includes the expansion F registers(Only T3H). One bank has 64K words (0 to 65535).

F 7 0

06

Bank number ... 00H: T3H internal registers

F0000 to F32767

01H: Expansion F registers (IC card) F0000 to F65535

02H: Expansion F registers (IC card) F0000 to F57343

⎯ 53 ⎯

Image 54

Contents T2N/T3H stations Important Information Preface Contents System configuration Introduction to S20LPStation hardware ∙ OverviewT2N include of S20LP Port SN325 SN325∙ Status LEDs S20LP port for T2N PU245NFor SN325 ∙ Reset switch only SN325 ∙ Station number setting switches∙ Transmission cable connectors ∙ Loader portLS overview Menu⎯ 10 ⎯ Specifications S20LP system specificationsS20LP-station specifications Scan transmission overview Setting the data send block by S-LS Allocation and network assignment by T-PDSSetting for data linkage Station number settingSettings on T-PDS Link PDS screen example Block Send Receive ⎯ 18 ⎯ Global ⎯ 20 ⎯ Settings on S-LS ⎯ 22 ⎯ ⎯ 23 ⎯ ⎯ 24 ⎯ ∙ Scan Transmission ∙ Scan Access∙ Start with Standby mode ∙ Message Transmission∙ Target Scan Time Data linkage example ∙ Settings on T-PDS Setting on S-LS LS setting screen 2 for STN #2 Cable connections ∙ Station down RAS functionBehavior in trouble ∙ Transmission cable breakageSelf-diagnostic function At initialization at power onDuring operation LED indication SN325T2N RAS information monitored in T2N/T3H Station status Online mapStandby map Loop map Only T2NRAS information monitored on S-LS Number 1-64 on the screen shows the Station numberSelf Station Station No.01 Offline Select the Station Number Click the Status Display Possible error message are as follows Station down informationInstruction format Instruction SpecificationExpanded data transfer instruction FunctionParameter and construction Transfer parameter tableSample program ∙ OperationRemarks Computer link protocol Message transmissionMessage transmission PC link protocol∙ Send Transfer parameters a CMDStatus B TermSTS Status Meaning Detailed Information Send completion status PC link protocol transmission Data write Transfer parametersRID Status See 7.3 5 for details on bits C, D, E, and F Important itemsXW/YW PC link protocol transmission Data read ⎯ 57 ⎯ SW067 Write enabled PC link protocol transmission program RemarksLength END Appendix Scan cycle⎯ 63 ⎯ PDS remote programming PDS Setup options screen