Toshiba TDP-MT500 owner manual Viwing Computer Images, Connecting this projector with a computer

Page 24

VIWING COMPUTER IMAGES

A. Connecting this projector with a computer

Preparations:

•Make sure that the power for the projector and computer are turned off.

•With a desk-top type computer, disconnect RGB cables connected to the monitor.

To DVI terminal

 

1

 

 

2

To monitor port

 

 

DVI

 

 

YCb/Pb Cr/Pr

Mini D-SUB 15pin-DVI

 

RS-232C

conversion cable

 

To DVI terminal

1

 

2

To DVI terminal

DVI

Cb/Pb Cr/Pr

DVI cable

RS-232C

 

In the case of analog connections:

1Connect the attached mini D-SUB 15pin- DVI conversion cable to DVI terminal of the projector.

2Connect the other end of the mini D-SUB 15pin-DVI conversion cable to the moni-

tor port of the computer.

•A conversion connector, analog RGB output adaptor, and/or the like may be needed depending on the type of computer to be connected.

•If a long cable other than the attached cable is used, the qual- ity of projected images may be degraded.

•When viewing picture images from a computer with analog connection, press DVI-ANALOG button of the remote control- ler.

•This projector does not comply with 3-line-signals (SYNC-ON- GREEN).

•This projector does not comply with chrominance signals.

In the case of digital connections:

1.Connect a commercially available DVI cable to DVI terminal of this projector.

2.Connect the other end of the DVI cable

to DVI terminal of the computer.

•A conversion connector, analog RGB output adaptor, and/or the like may be needed depending on the type of computer to be connected.

•If a long cable other than the attached cable is used, the qual- ity of projected images may be degraded.

•When viewing picture images from a computer with digital con- nection, press DVI-DIGITAL button of the remote controller.

•Also, read the instruction manual of the other equipment to be connected.

•If VGA60 signal outputs at the startup of the computer, the projected image may not be displayed properlyÑü for example, the position of the displayed image may be shifted. However, this is not a failure (Non-compliant signal).

•No speaker for audio outputs is stored in this projector. To reproduce audio signals, use the speakers of the personal computer, or connect necessary audio equipment.

•Consult the delivery agent of this projector on the detailed connections, as needed.

B. Plugging power cord

Plug the power cord in the same way as described in “Connecting to video equipment”. See Page 17.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents TDP-MT500 Safety Precautions Important Safety Instructions Power Sources VentilationSource of Light Power-Cord Protection CleaningHeat Water and MoistureAccessories Object and Liquid EntryDo not place the product verti- cally AttachmentsDamage Requiring Service Replacement PartsService Safety CheckAir exhaust UsePower Supply Cord Selection Important PrecautionsPlace and Manner of Installation Save Original Packing MaterialsAvoid Volatile Liquid Declaration of ConformityTable of Contents Checking accessories Inserting the dry batteries into the remote controllerPreparation Name and function of operational parts of the projector Zoom ring 18How to use remote controller Name and function of operational parts of remote controllerOn the picture quality adjusting buttons Operational range of remote controller Front of projector Vertical directionsSetting UP Setting up screenBasic setup Adjusting projection angleWhere the screen size is 16 Screen size and Projection distanceWhere the screen size is 4 Wide Height HViewing Video Images Connecting to video equipment that has DVI-D terminal Viewing Video ImagesPlugging power cord ConnectionPress Power button Select an input signalAdjust focus by turning the focus ring Making projectionPress Power button again Turn OFF the main power switch Turn to indication OIf the projected image frame is deformed to a trapezoid On setting Aspect Image angle How to change the settingsConnecting this projector with a computer Viwing Computer ImagesTor port of the computer Turn on the main power switch Turn to indication Power button / Power indicatorPress Power button again Setting with Menus Menu constructionHow to make menu setting Items that can be set with menus Picture MenuProfessional Picture Menu On the memory for projected image quality VideoComponent 1 DVI-ANALOG/DIGITAL Adjusting projected images Adjusting color Color Thickness and TintSetting projected images sharper or softer Sharpness Color ThicknessUSER1 USER2 Setting with Menus Replacing the Lamp / Cleaning the Projector How to replace the lampCleaning dust in the intake vent Cleaning the projectorCleaning the lens Troubleshooting Picture images are not projected on screenTroubleshooting Indicators Power Lamp Temp StateState RemarkWhen Asking Installation Work Dimensional drawings for referencesTerminals TDP-MT500Type of connectable signals VGASvga XGA
Top Page Image Contents