Toshiba TDP-MT500 owner manual When Asking Installation Work, Dimensional drawings for references

Page 39

WHEN ASKING INSTALLATION WORK

In the case of suspending the projector from ceiling and viewing the projected images from the front side:

When suspending the projector from ceiling, use the separately sold dedicated metal bracket (see Page 38). Also, be sure to ask a special worker who received train- ing of the installation work to do the work. Consult the delivery agent of the projector about the details of the installation work.

•If the projector is damaged by using any other suspension bracket than the dedicated one or due to any problem of the environment in which the suspension metal bracket is in- stalled, Mitsubishi Electric Corporation will not compensate the damage even if the product is still under warranty.

Projector

Screen

•In the case of the suspension from ceiling, set the projection method in the setting menu to “Ceiling suspension”. Refer to Page 27 for the detail.

•Ask the installation worker to provide a power breaker for the projector. When the projector is not used, be sure to turn off the main power for the projector with the breaker.

•Where the projector is suspended from ceiling, the bright- ness of the projected images may be less brighter than where it is set on floor. However, this is not a failure.

•Do not install the projector where its exhaust vent is directly exposed to the wind from an air conditioner or the like. Such installation may cause failures of the projector.

•Do not install the projector near a fire alarm, because hot air is exhausted form the vent of the projector.

Dimensional drawings (for references)

251

9

308

 

235

 

66

96

108

In the case of installing the projector so that the picture images are projected onto a semitranspar- ent screen and viewed them from the rear side of the screen:

When installing the projector, be sure to ask a special worker who received training of the installation work. Consult the delivery agent of the projector about the details of the installation work.

Screen

Projector

•When viewing projected images from the rear side of the screen, set the projection method in the setting menu to “Rear”. Refer to Page 27 for the detail.

 

 

280

 

 

 

16

16

 

 

167

168

 

181

166

 

 

44.5

53.5

33.5

 

 

 

 

28

199

28

 

 

 

 

 

 

254

 

 

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents TDP-MT500 Safety Precautions Important Safety Instructions Power Sources VentilationSource of Light Water and Moisture Power-Cord ProtectionCleaning HeatAttachments AccessoriesObject and Liquid Entry Do not place the product verti- callySafety Check Damage Requiring ServiceReplacement Parts ServiceUse Air exhaustSave Original Packing Materials Power Supply Cord SelectionImportant Precautions Place and Manner of InstallationDeclaration of Conformity Avoid Volatile LiquidTable of Contents Checking accessories Inserting the dry batteries into the remote controllerPreparation Zoom ring 18 Name and function of operational parts of the projectorHow to use remote controller Name and function of operational parts of remote controllerOn the picture quality adjusting buttons Vertical directions Operational range of remote controller Front of projectorAdjusting projection angle Setting UPSetting up screen Basic setupScreen size and Projection distance Where the screen size is 16Wide Height H Where the screen size is 4Viewing Video Images Viewing Video Images Connecting to video equipment that has DVI-D terminalConnection Plugging power cordMaking projection Press Power buttonSelect an input signal Adjust focus by turning the focus ringPress Power button again Turn OFF the main power switch Turn to indication OIf the projected image frame is deformed to a trapezoid How to change the settings On setting Aspect Image angleConnecting this projector with a computer Viwing Computer ImagesTor port of the computer Power button / Power indicator Turn on the main power switch Turn to indicationPress Power button again Menu construction Setting with MenusHow to make menu setting Items that can be set with menus Picture MenuProfessional Picture Menu On the memory for projected image quality VideoComponent 1 DVI-ANALOG/DIGITAL Color Thickness Adjusting projected imagesAdjusting color Color Thickness and Tint Setting projected images sharper or softer SharpnessUSER1 USER2 Setting with Menus How to replace the lamp Replacing the Lamp / Cleaning the ProjectorCleaning dust in the intake vent Cleaning the projectorCleaning the lens Picture images are not projected on screen TroubleshootingTroubleshooting Remark IndicatorsPower Lamp Temp State StateDimensional drawings for references When Asking Installation WorkTDP-MT500 TerminalsXGA Type of connectable signalsVGA Svga
Top Page Image Contents