Toshiba TDP-MT500 owner manual Setting with Menus

Page 33

SETTING WITH MENUS

Adjusting picture images sent from computers

This projector automatically sets an appropriate signal processing format according to the image signal sent from computers. However, depending on the type of the computer, the image signals may not be projected properly. On this occasion, a countermeasure should be taken as follows:

1.Reveal the setting menu.

2.Select “Setting signals” by pressing Å £, Å• buttons.

3.Press ENTER button.

•The signal setting menu appears.

4.Select “Auto” by pressing Å £, Å• buttons.

5.Press ENTER button.

•Automatic setting is made so that an appropriate setting may be obtained for the input signal. To cancel the menus:

6. Press MENU button.

If the computer images can not be projected properly with the above operation, adjust the images using menus as follows:

These settings can be stored in memory of the projector. How to adjust computer images using menus:

If the following phenomena are observed, adjust as follows: Projected images are shifted to the left or right:Å c.

Adjust “Horizontal position” in the signal setting menu. Every time ? button is pressed, the projected image is shifted to the left. Every time ? button is pressed, the projected image is shifted to the right. Projected images are shifted up or down:Å c.

Adjust “Vertical position” in the signal setting menu. Every time ? button is pressed, the projected image is shifted downward. Every time ? button is pressed, the projected image is shifted upward.

Projected images blink. Projected images are blurred:Å c. Adjust “Fine” in the signal setting menu.

A wide streak pattern appears on the projected images:Å c. Adjust “Dividing ratio” in the signal setting menu.

Åú Usually, do not change the settings in the signal setting menu.

A simple method of adjusting the position of projected images

Adjusting horizontal position:

1.Align the left edge of the projected image with the left side of the screen by adjusting “Horizontal position”. Then, align the right edge with the right side of the screen by adjusting “Dividing ratio”.

2.Repeat the above adjustments to align the horizontal position.

Adjusting vertical position:

3.Align the upper edge of the projected image with the upper side of the screen by adjusting “Vertical position”.

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents TDP-MT500 Safety Precautions Important Safety Instructions Power Sources VentilationSource of Light Cleaning Power-Cord ProtectionHeat Water and MoistureObject and Liquid Entry AccessoriesDo not place the product verti- cally AttachmentsReplacement Parts Damage Requiring ServiceService Safety CheckUse Air exhaustImportant Precautions Power Supply Cord SelectionPlace and Manner of Installation Save Original Packing MaterialsDeclaration of Conformity Avoid Volatile LiquidTable of Contents Checking accessories Inserting the dry batteries into the remote controllerPreparation Zoom ring 18 Name and function of operational parts of the projectorHow to use remote controller Name and function of operational parts of remote controllerOn the picture quality adjusting buttons Vertical directions Operational range of remote controller Front of projectorSetting up screen Setting UPBasic setup Adjusting projection angleScreen size and Projection distance Where the screen size is 16Wide Height H Where the screen size is 4Viewing Video Images Viewing Video Images Connecting to video equipment that has DVI-D terminalConnection Plugging power cordSelect an input signal Press Power buttonAdjust focus by turning the focus ring Making projectionPress Power button again Turn OFF the main power switch Turn to indication OIf the projected image frame is deformed to a trapezoid How to change the settings On setting Aspect Image angleConnecting this projector with a computer Viwing Computer ImagesTor port of the computer Power button / Power indicator Turn on the main power switch Turn to indicationPress Power button again Menu construction Setting with MenusHow to make menu setting Items that can be set with menus Picture MenuProfessional Picture Menu On the memory for projected image quality VideoComponent 1 DVI-ANALOG/DIGITAL Adjusting color Color Thickness and Tint Adjusting projected imagesSetting projected images sharper or softer Sharpness Color ThicknessUSER1 USER2 Setting with Menus How to replace the lamp Replacing the Lamp / Cleaning the ProjectorCleaning dust in the intake vent Cleaning the projectorCleaning the lens Picture images are not projected on screen TroubleshootingTroubleshooting Power Lamp Temp State IndicatorsState RemarkDimensional drawings for references When Asking Installation WorkTDP-MT500 TerminalsVGA Type of connectable signalsSvga XGA
Top Page Image Contents