Toshiba G8000 operation manual Electrical Specification, Do not open the front cover

Page 53

12.3Electrical Specification

warning

DO NOT open the front cover.

Electric shock, burns or other personal injuries may occur if untrained personnel open the front cover.

AC Input Rated Capacity	100 kVA (80 kW)	150 kVA (120 kW)	225 kVA (180kW)	300 kVA (240 kW)
Input Voltage		480 V ( +10% to -15% ), 3-Phase 3-Wire
Input Frequency		60 Hz ±5%
Input Power Factor		0.95 – 1.00 Lagging ( at 100% Load )
Current Harmonic Distortion		4% Maximum ( at 100% Load )
Input Capacity Required	107 kVA	154 kVA	232 kVA	309 kVA
Circuit Breaker Rating At 480V	150 A Trip	225 A Trip	350 A Trip	500 A Trip
Input

DC Input Rated Capacity	100 kVA (80 kW)	150 kVA (120 kW)	225 kVA (180 kW)	300 kVA (240 kW)
Voltage Window		288 – 414 V
Recharge Voltage Regulation		± 1.5%

AC Output Rated Capacity	100 kVA (80 kW)	150 kVA (120 kW)	225 kVA (180 kW)	300 kVA (240 kW)
Output Voltage		480/277 V ± 1%, 3-Phase 4-Wire
Output Power Factor		0.8 Lagging
Voltage Distortion	3% with 100% Linear Load / 5% with Non-Linear Load
Transient Voltage Regulation		< ± 2%
Transient Settling Time		< 50 ms
Crest Factor		< 2.0
Output Frequency		60 Hz ± 0.01% ( at Free-running Mode)
Synchronous Window To Utility Line		59 Hz – 61 Hz
Frequency Slew Rate		1 Hz/Sec
Over Load Rating	100%-Continuous / 125% – 10 min. / 150% – 1 min.

G8000 Series Installation and Operation Manual

45

Image 53

Contents G8000 Series Page Document November Qualified Personnel only Uninterruptible Power System UPS Toshiba’s Customer Support Center PurposeToshiba Customer Support Center Toshiba International CorporationTable of Contents 11.3 Introduction Prohibited Symbol indicates do not take action General Safety InstructionsSymbols Qualified Personnel Signal WordsFactory Authorized Personnel Important Safety InstructionsDisclaimer Safety PrecautionsKeep the area arround the UPS clean General MaintenanceTransporting/Unpacking Do not tilt the UPS more than 10 from upright positionAvoid vibration or shock exceeding 0.5G Do not transport, move, store, or place the UPS on its sideInspection/Storage Keep the Specified Clearance around the UPS Installation PrecautionsInstall the UPS in a controlled environment Do not block air vents Do not install the UPS where water may fall on itEnvironment standard Installation PrecautionsPage Perform wiring and connections with correct polarity Wiring/ConnectionConnect only one 1 ground wire to the earth ground terminal Follow the torque criteria for tightening screwsFor 100, 150, 225KVA GND 150/225 kVA UPS Warning Labels Model Unit Shipping Weight and Dimensions300 kVA UPS Exterior Dimensions Inches Transporting 8.5 show examples of acceptable and unacceptable operations Transporting By CraneTransporting UPS by Forklift Transporting By ForkliftStorage/Operating Environment Operating PrecautionsPage Qualified Personnel shall Maintenance PrecautionsQualified Personnel only Do not open or mutilate the batteries DisposalDo not dispose of the batteries in a fire Installation UPS Clearance UnpackingAnchor Bolts Anchor Bolt Installation DetailExternal Wiring Diagram UPS WiringBlock Number Cable Size Tightening Torque Terminal Blocks and Power CablesRecommended Cable Size & Tightening Torque for 150 kVA UPS AC Input Bypass AC Output Battery Control Wires CRA-1/OL Plate #4 Terminal Bus # Recommendation Bus Number Cable Size Tightening TorqueBe sure to ground the UPS as specified Grounding WireExternal Breakers G8000 100 kVA G8000 150/225 kVA Signal Name Operation Control Wires10 Connection Between UPS, Battery Cabinet & Bypass Breaker 11 Grounding Configuration with Input Neutral Grounded Grounding ConfigurationRecommended Configuration for delta-input Grounding Configuration without input neutral15 Grounding Configuration with CORNER-GROUNDED DELTA-INPUT Grounding Configuration with corner-grounded delta-inputGeneral Specification UPS SpecificationsMechanical Specification Terms Specification RemarksRated Capacity 150 kVA 225 kVA 300 kVA Do not open the front cover Electrical SpecificationUPS may not respond if the button press is too short Operator InterfaceGraphic display Panel KEY-SWITCH/OPERATING Buttons Key-Switch and ButtonsGraphic display Panel LCD/LED INDICAtors 13.2 LCD/LED IndicatorsName Description LCD IndicatorsAC-VO AC- I O 50% Normal DisplayVolt Freq .0Hz 50%BYP I/P-V Freq .0Hz AC I/P-V Freq .0HzDC-V BATT-V BATT- I 0A 32TIM09-09-06 Fault DisplayAbbreveations LCD ScrollOperating the UPS Epo and Control Power supply operating switchesPerform the pre-operational check before operating the UPS Operation TypesPre-operational Check Procedure to start the UPS is shown in Steps Startup ProceduresAC Vo 480 AC Io 50% Bypass LED is on Switch Power Supply UPS→BypassStop DC-V 0 BATT-V 0 BATT-I 0 a Complete ShutdownMake sure that the Float Charge LED is on Changing Between Float Charge and Equalize ChargeMake sure that the Equal Charge LED is on Types of Errors TroubleshootingEmergency Power Off EPO 09-09-06 Faults and Warnings Data ScreenFault Display LCD Fault & Warning DisplaysOver Heat Fault MessagesLCD Message Indication Description Button functions LCD Scroll w/ faults or warningsRestoring UPS Operation Contact Toshiba in the event of malfunction or faultDo not attempt to modify or relocate the UPS Do not open the front and/or rear panelsPage Page Industrial Division

Related manuals

Manual 74 pages 20.32 Kb

Manual 1 pages 30.84 Kb