Siemens 2000 manual Starting up the optiPoint 410/420, Installing the Telephone

Page 13

Installing the Telephone

Setting Up the Telephone

Starting up the optiPoint 410/420

7Only use switches in the LAN, to which the optiPoint 410/420 is connected. An operation at hubs can cause serious malfunctions in the hub and in the whole network.

The Western plugs of all cable connections must audibly snap into place.

•Plug the short end of the handset cable into the handset and the other end into the connector 7 at the bottom of the telephone and feed the cable through the guide channel in the base unit.

•Using the headset connector:

Plug the jack of the headset cable into connector 6 at the bottom of the telephone and feed the cable through the guide channel in the base unit.

•Using optiPoint modules (4):

Mount this device following the instructions in the installation guide (A31003-H8400-B934-*-6ZD1).

•Using adapter (7, 8):

Mount this device following the instructions in the installation guide (A31003-H8400-B934-*-6ZD1).

•Using the external keyboard:

Plug the keyboard cable into the USB connector 9 at the bottom of the telephone.

•Using a LAN connection to PC:

Plug the jack of the connection cable into the connector 5 at the bottom of the telephone.

Only if power not supported by LAN:

7Use only the plug-in power supply unit fitting the optiPoint 410/420:

– GER/IM: AUL:06D1284

– GBR: AUL:06D1287

– USA: AUL:51A4827

– Plug the plug-in power supply unit into the mains.

– Plug the connector 3 at the bottom of the telephone into the plug-in power supply unit.

• Plug the jack of the LAN cable into the connector 4 at the bottom of the telephone and connect the cable with LAN.

• Feed the cables through the relief on the back of the housing and fix them by means of the cable clip.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents
HiPath Administrator ManualFor Your Safety Safety PrecautionsSafety Precautions Protection of the TelephoneImportant Notes Location of the TelephoneContents Factory Default Settings Administration scenariosAlphabetical Reference EditorsIndex Data Visualisation optiPoint 410 entry onlyAbout the Manual General InformationProduct Identification Echo EffectVoIP Security Safety Precautions for IP TelephonyGeneral Information Reference to operation steps SafetyS o uor Operating the telephoneOptiPoint 410/420 economy/economy plus/stan- dard/advance OptiPoint 410 entryVoIP Security Properties of the Telephone ModelsModel Installing the Telephone Setting Up the TelephoneConnectors on the bottom of the telephone Starting up the optiPoint 410/420 Installing the TelephonePreparing for Operation Entering the administration areaAll configuration types TroubleshootingOnly if no Dhcp server 1st Function key OptiPoint 410 entry2nd Function key Only if you are working in a Virtual LAN Vlan Enter IP address of the optiPoint 410 entry to edit see ÆOther settings Error handlingAdministration AdministrationRemote maintenance through LAN Locally on the telephoneOptiPoint 410/420 economy/ economy plus/standard/advance Access to the Administration MenuPress keys simultaneously OptiPoint 410/420 economy/economy plus/standard/advance ConfigurationsDhcp IP Assignment Terminal IP AddressVlan Method Default RouteVlan ID QoS Layer Options LAN Port 1 ModeSubscriber Password LAN Port 2 ModeSubscriber Number Display Test DiagnosticsLED Test Audio Loop Test Key TestExecute test RAM TestPing change target Ping TestSLK Test Line StatusRestart By pulling the power plugWeb-based Management Tool After restartError Messages Other error messages View settings Entering the administration areaOptiPoint 410 entry Function Codes Reset factory settings LEDs on the phone No Default RouteNo terminal screen No IP Address is setNo Participant No. / password No Default Route is setNo terminal screen is set No networkPBX does not react No PBX addressLog in failed Ldap Configuration Firmware UpdateOptiPoint display module Installing the Ldap Template Configuring the Ldap ServerOptiPoint display module OptiPoint application module OptiPoint application module Installing an Ldap TemplateGeneral Web-based Management ToolWeb-based Management Tool PreparationOpen web-based management tool Http//IP of the telephoneWeb-based Management structure Change administrator password Administrator ActionsGeneral Information General InformationRestart terminal Factory Reset Clear screenlock passwordOnly for optiPoint 410/420 standard/advance available Clear user dataJava Http Settings Web-based Management ToolAdministrationLdap settings ApplicationsWAP Favourites WAP gatewayMiscellaneous Diagnostic Tests Test results Audio settingsAudio File transfer ENB FTP Settings Java FTP SettingsFile Transfer optiPoint 410/420 entry/economy/economy plus Network and Routing NetworkSnmp settings Quality of Service QoSQoS Data Collection System DLS Settings Gateway settingsPort Control Port SettingsTime Settings Voip Encryption Settings Srsr SettingsDescription of functions Alphabetical ReferenceAlphabetical Reference Action On SubmitCancel Mobility Password Administration PasswordApplication Filename Application VersionCodec Codec Audio Mode UseCodec Independent Threshold Values Compressing Codec Threshold Values CompressionDaylight saving Debug InterfaceDefault Vlan ID Default Sntp IPDhcp DLS Server PortDNS Addresses External Access CodeDomain Name DSM FilenameEmergency Number FTP PasswordFTP Account Name FTP Server AddressFTP Username FTP SettingsG722 codec Gateway AddressHttps International Dial Prefix Http UsernameIP Routing Java GatewayL2/L3 Voice/Signalling L2 DefaultJitter Buffer Bandwith Possible application LAN Port SettingsLanguage Ldap Server IP AddressTemplate-String Declaration Ldap template exampleSyntax of the Ldap template file Example for assumption Copy & PastePort Function LEDs on optiPoint 410/420 right row Ldap Template FilenameLocal Area Code MIB-II Error CountLocal Country Code Local District CodeNational Dial Prefix Minimal Session LengthNon-Compressing Codec Threshold Values Observation IntervalQCU Standby Address QCU Home AddressQDC Server QoS L2/L3Service Agent Report ModeRestart Terminal RTP Port BaseSnmp Srsr Enabled Srsr Automatic Switch BackSrsr Switch To Home Expiry Timeout Srsr Switch To Home Retry CountSrsr Tctest Expiry Timeout Srsr Switch To Standby Retry CountSrsr Tctest Retry Count System TypeTime Window Time SourceTimezone offset USB KeyboardWAP Connection Type WAP PasswordWAP Username WAP URL Cornet IP TS Abbreviations and Specialized TermsDLS DNSFTP ENBHFA HttpLdap LANLCD LEDPBX MIBPing PSSSLK SIPVlan SntpURL SwitchVoIP WAPSetting up the FTP server Administration scenariosSetting up the FTP server Administration scenarios Installation and configurationStart up not successful Check handset functionalitiesCheck LAN connection Determine the software versionImprove speech quality Number Editor EditorsIP Number Editor Number EditorEditors Teminal Mask EditorBit Block Text Editor Text EditorKey 10x 11x 12x 13x 14x 15x 16x 17x 18x 19x 20x 21x 22x 23x OptiPoint 410/420 economy/economy plus/standard/advanceStandard value Factory Default SettingsFunction Standard value Vlan Dhcp Vlan ID Password Function setting Password FunctionsTaste Funktion HiPath 3000/5000 Key-LayoutStatus Messages Data Visualisation optiPoint 410 entry onlyBinary encoded Ascii table Data Visualisation optiPoint 410 entry onlyBinary encoded Ascii table Technical data101 102 Technical dataOperation Codes Summary Administration InterfaceOptiPoint 410/420 OptiPoint 410/420Operation Codes Summary104 Operation Codes SummaryoptiPoint 410/420OptiPoint 410 entryOperation Codes Summary Further functions105 Menu structureoptiPoint 410/420 Menu structure106 Index Index107 108 Https109 SrsrBestell-Nr. A31003-A2056-B415-7-76A9
Top Page Image Contents