Siemens Panel PC 870 appendix Fixation Step, Fixation using clamping saddles

Page 17

Release 11/02

Unpacking and Installing the Panel PC 670/870

Fixation

Step 8

Fixation using clamping saddles

Applies to both centralized and decentralized designs:

Skip this working step if screw mounting fixation has been decided upon.

The clamping saddles and threaded pins required for the installation are part of the material supplied in the delivery content. Proceed as follows:

1.Insert the Panel PC 670/870 or operating unit in the installation cut-out from the front.

2.From the back, fasten the operating unit in the installation cutout by tightening the setscrews (torque: 0.4 - 0.5 Nm) of the six clamps (see Figure 2–2).

In the case of a decentralized design, secure the computer as described in Step 11.

Otherwise, installation is complete. Refer to Chapters 2.1 to 2.3 for information concerning the position of the interfaces, the operating panel and the operating system. Then continue with Step 11.

Fixation using screw mountings

Applies to both centralized and decentralized designs:

Skip this working step if clamping saddle fixation has been decided upon. Proceed as follows:

1.Drill appropriate holes in the installation cut-out in accordance with the specifications to L4 and L5 in Figure 1–6.

2.Carefully break out the drill hole caps on the front of the operating unit.

Drill hole caps

Figure 1–8 Drill holes with caps

SIMATIC Panel PC 670/870 Start-Up Instructions

1–9

Image 17
Contents Release 11/02 Panel PCStart-Up Instructions Qualified Personnel Safety GuidelinesCorrect Usage TrademarksDocumentation 1PrefacePurpose Trademarks NotationAvailable worldwide Customer and Technical SupportOther Sources of Assistance Simatic Customer Support Online ServicesTraining Center Contents Electromagnetic Compatibility General Information Appendix Unpacking and Checking the Delivery Contents Unpacking and Installing Panel PC 670/870Entering the operating unit number Step Unpacking and Installing the Panel PC 670/870 Release 11/02Installation notes Installation of the Panel PC 670/870Installation angle Step Degree of protection and type of fixation Step Step Select installation cut-outInstallation cut-out for Panel PC Applies to both centralized and decentralized designs Making the installation cut-out StepFixation Step Fixation using clamping saddlesFixation using screw mountings Unpacking and Installing the Panel PC 670/870 Release 11/02 Not permitted where an LS240 drive is installed Installation of the Computer UnitAn installation angle of ±15 is permitted in this position 11 Dimensions for installation of the computer unit Installation StepUnpacking and Installing the Panel PC 670/870 Release 11/02 Computer unit Connecting and Switching On Panel PC 670/870Interfaces Mouse AC/DC power supply connectionCOM 1/Modem/Programmable Logic Controller PLC COMGeneral information Step Operating unit13 LPT1 KeyboardFront view of the operating unit Operating Units with Keypad FrontsKeyboard Operating Units with Touchscreen FrontsConnection Step Power SupplyOperation Switching on Step ChecklistInitial Startup Panel PC 670/870 in a centralized designLicense number Selecting the screen resolution Screen resolution and panel type selection StepPanel PC Operating SystemWindows 98 only applies to Panel PC Special featuresPower management USB Keyboardcontroller Windows NT 4.0 TMDhcp utility Restrictions Bios settingsService Pack Auto Logon WindowsWindows XP Operating system not installed Defragmenting the hard disk Step Installing Additional User SoftwareProcedure USB interfaces Use of USB Peripheral DevicesSimatic Panel PC 670/870 Start-Up Instructions Panel PC 670/870 Windows Panel PC 670/870 Windows NT 4.0 with USB StackPanel PC 670 Windows Panel PC 670 Windows XPSimatic Panel PC 670/870 Start-Up Instructions Normal Operation Operating the Panel PC 670/870Activation Shut DownRestore CD Data Backup and Restoring the Operating SystemBackup copy of the hard disk drive Windows 2000, Windows XP Recovery CDWindows NT, Windows \drivers.w98 \drivers.nt4 \drivers.w2k \drivers.wxp Modifying touch settings Touchware settingsAdditional Drivers and Applications Documentation & Drivers CDRepeat calibration Touch Settings tab controlMicroTouch touchscreen properties Select the option 2 Point for Calibration Style If this happens Call KeypadFunction Keypad front FileSimatic SOM safecard on motherboard Setdisplay TouchInputPCSetbrightness KeyHook 11 CheckLanguageID CheckLanguageIDChanging user interface languages Language settings13 Language setting 14 Standard language Changing the standard languagePulse shaped interference Electromagnetic CompatibilityInterference emission Sinusoidal wave interferenceGeneral Information Faulty pixels in displayDisposal Pixel numberFM approval Abbreviations AppendixAppendix Release 11/02