Dell GX200 manual Microprocessor/Cooling Fan/Heat Sink Assembly

Page 76

1Securing clips (2)

To reinstall a RIMM, perform the following steps:

1.Locate the plastic securing clips at each end of the socket (see Figure 26).

2.Press the clips outward until they snap open.

3.Press the RIMM straight into the slot running down the center of the socket until the securing tabs snap into place around the ends of the RIMM.

4.Replace the computer cover.

5.Reset the chassis intrusion detector.

Figure 26. RIMM Installation

1 Securing clips (2)

2 Notches (2)

6. Run the Dell Diagnostics to verify that the RIMMs are operating properly.

Microprocessor/Cooling Fan/Heat Sink Assembly

Figure 27. Microprocessor/Cooling Fan/Heat Sink Assembly

1Cooling fan/heat sink assembly

2ZIF socket

3Retaining clip

CAUTION: The microprocessor/heat sink assembly can get extremely hot. Be sure that the assembly has had sufficient time to cool before you touch it.

NOTE: Dell recommends that only a technically knowledgeable person perform this procedure.

To replace a microprocessor, perform the following steps:

Image 76

Contents Initial release 18 April Last revised 31 Jul Precautionary Measures OverviewRecommended Tools You have removed the computer coverInternal Views Computer CoverComputer Cover Replacement Eject, Power, and Reset Buttons Front-Panel InsertsReset the chassis intrusion detector Chassis Intrusion SwitchControl Panel Drives Inch Diskette DriveInch Drive Remove the diskette drive and bracketHard-Disk Drive to Bracket Installation If not already done, remove the computer coverSystem Power Supply Replace the computer coverExpansion-Card Cage Riser BoardsSystem Board Components PCI/ISA Riser Board OptionalSystem Board Jumpers Expansion Cards System-Board Jumper Settings DescriptionSystem Board Labels Expansion-Card Removal Expansion-Card InstallationRemove the computer cover Memory Removing a RimmMicroprocessor/Cooling Fan/Heat Sink Assembly Microprocessor/Cooling Fan/Heat Sink AssemblySystem Battery Microprocessor Package InstallationSystem Board System Board RemovalBack to Contents Microprocessor/Airflow Shroud/Heat Sink Assembly Computer Cover Internal View Inside the ChassisExpansion-Card Cage Inch Diskette Drive Removal Remove the hard-disk drive cageInch Drive Removal 25-Inch Drive Removal Hard-Disk Drive Replacement Hard-Disk Drive InsertionSystem Power Supply Rotation System Power Supply RemovalRotate the system power supply System Power Supply InstallationSystem Board Jumpers Expansion Cards Expansion-Card Replacement Expansion Card RemovalMidsize Chassis PCI Riser Board Microprocessor/Airflow Shroud/Heat Sink Assembly Rimm InstallationHeat Sink Assembly Removal Securing the microprocessor package Disconnect all cables from the system board Back to Contents Overview Mini Tower Chassis Orientation View Computer Cover Replacement Front Bezel Front Bezel RemovalFront-Panel Inserts Chassis Intrusion Switch Remove the control panel from the front panel Diskette Drive RemovalRemove the front bezel Drive Bracket AttachmentNew Drive Insertion Remove the computer cover Remove the front bezel Hard-Disk Drive Removal From BracketDrive Bracket Insertion Into Chassis System Power Supply Mini Tower Chassis PCI Riser Board Mini Tower Chassis PCI/ISA Riser Board System Board Jumpers CD-ROM audio interface connector Expansion Card Installation Memory Microprocessor/Airflow Shroud/Heat Sink Removal Microprocessor package Socket release lever ZIF socket System Battery Remove the airflow shroud from the microprocessor Replace the airflow shroud Replace the expansion-card cage Overview Orientation View Computer Cover Replacement Eject and Power Buttons Remove the drive shelf Remove the power supplyChassis Intrusion Switch Preliminary Steps Hard-Disk DriveDrive Bracket Removal Hard-Disk Drive Cable Attachment CD-ROM Drive CD-ROM Drive RemovalSystem Power Supply Riser Board PCI Riser BoardSystem Board Jumpers System-Board Jumper Settings Description Bit PCI Expansion Card Example Expansion Card Removal Memory Microprocessor/Cooling Fan/Heat Sink Assembly Microprocessor Package Removal Replace the computer cover and restart the system Replace the drive shelf assembly