NETGEAR WNR1000v3h2 manual Using the Router as a Dhcp Server, Using Address Reservation

Page 50

N150 Wireless Router User Manual

-RIP-2Mcarries more information than RIP-1 and uses multicasting.

Using the Router as a DHCP Server

By default, the router functions as a DHCP server, allowing it to assign IP, DNS server, and default gateway addresses to all computers connected to the router’s LAN. The assigned default gateway address is the LAN address of the router. The router assigns IP addresses to the attached computers from a pool of addresses specified in this screen. Each pool address is tested before it is assigned to avoid duplicate addresses on the LAN.

Note: For most applications, the default DHCP and TCP/IP settings of the router are satisfactory. Click the link to the online document TCP/IP Networking Basics in Appendix B for an explanation of DHCP and information about how to assign IP addresses for your network.

To specify a pool of IP addresses to be assigned, set the starting IP address and ending IP address. These addresses should be part of the same IP address subnet as the router’s LAN IP address. Using the default addressing scheme, you should define a range between 192.168.1.2 and 192.168.1.254, although you might wish to save part of the range for devices with fixed addresses.

The router delivers the following parameters to any LAN device that requests DHCP:

•An IP address from the range you have defined

•Subnet mask

•Gateway IP address (the router’s LAN IP address)

•Primary DNS server (if you entered a primary DNS address in the Basic Settings screen; otherwise, the router’s LAN IP address)

•Secondary DNS server (if you entered a secondary DNS address in the Basic Settings screen)

To use another device on your network as the DHCP server, or to manually specify the network settings of all of your computers, clear the Use Router as DHCP Server check box. Otherwise, leave it selected. If this service is not selected and no other DHCP server is available on your network, you need to set your computers’ IP addresses manually or they will not be able to access the router.

Using Address Reservation

When you specify a reserved IP address for a computer on the LAN, that computer always receives the same IP address each time it accesses the router’s DHCP server. Reserved IP addresses should be assigned to computers or servers that require permanent IP settings.

50 Chapter 4: Customizing Your Network Settings

Page 49 Page 51
Image 50
Page 49 Page 51
Contents N150 Wireless Router WNR1000v3h2 Statement of Conditions Technical SupportTrademarks Revision HistoryTable of Contents Customizing Your Network Settings Troubleshooting Using the Setup Manual Configuring Basic ConnectivityLogging In To Your Wireless Router Configuring Basic Connectivity Selecting a Language for Your Screen Display Configuring Basic Connectivity Your Internet Connection Does Not Require a Login Configuring Your Internet Settings Using the Setup WizardViewing and Configuring Basic Internet Settings No login required Your Internet Connection Does Require a Login Login required Configuring Basic Connectivity Setting Up and Testing Basic Wireless Connectivity Configuring Basic Connectivity Click Setup Access List Safeguarding Your Network Safeguarding Your NetworkChoosing Appropriate Wireless Security To configure the wireless network, you can Wireless Security Options Other Features That Enhance SecurityRecording Basic Wireless Settings Setup Information If WEP Authentication is used, circle one Shared Key or AutoChanging Wireless Security Settings Viewing Basic Wireless SettingsSafeguarding Your Network Configuring WEP Wireless Security Safeguarding Your Network Configuring WPA-PSK and WPA2-PSK Wireless Security Viewing Advanced Wireless Settings Using Push N Connect Wi-Fi Protected Setup Push Button Configuration Using the Physical Push ButtonUsing the Router’s Security PIN Security PIN EntryConfiguring the WPS Settings Using the Wireless Client’s Security PINAdding Additional WPS-Enabled Clients Restricting Wireless Access by MAC Address Adding Additional Non-WPS-Enabled ClientsSelect the Turn Access Control On check box Adding Guest Networks To add a guest network, do the followingChanging the Administrator Password Backing Up Your Configuration Understanding Your Firewall Restricting Access From Your Network Content Filtering OverviewBlocking Access to Internet Sites Blocking Access to Internet Services To block access to Internet services Blocking Services by IP Address Range Scheduling BlockingViewing Logs of Web Access or Attempted Web Access Log Entry DescriptionsConfiguring E-mail Alert and Web Access Log Notifications Setting the Time Zone Using the LAN IP Setup Options Customizing Your Network SettingsConfiguring a Device Name Configuring LAN TCP/IP Setup ParametersUsing the Router as a Dhcp Server Using Address ReservationTo edit or delete a reserved address entry Using a Dynamic DNS ServiceTo reserve an IP address Click Edit or DeleteSelect the Use a Dynamic DNS Service check box Configuring the WAN Setup OptionsTo configure for a Dynamic DNS service Setting Up a Default DMZ Server Disabling Port Scan and DoS ProtectionConfiguring NAT Filtering Configuring Static RoutesSetting the MTU Size Responding to a Ping on the Internet WAN PortTo add or edit a static route Customizing Your Network Settings Fine-Tuning Your Network Allowing Inbound Connections to Your NetworkFine-Tuning Your Network How Port Triggering Changes the Communication Process Web server then sends this reply message to your routerHow Port Forwarding Changes the Communication Process Configuring Port Forwarding to Local Servers How Port Forwarding Differs from Port TriggeringAdding a Custom Service To configure port forwarding to a local serverApplication Example Making a Local Web Server Public Click Edit Service or Delete Service to make changesEditing or Deleting a Port Forwarding Entry To edit or delete a port forwarding entryConfiguring Port Triggering Clear the Disable Port Triggering check box Using Universal Plug and Play To turn on Universal Plug and PlayOptimizing Wireless Performance Reduce interference Identify critical wireless linksChoose your settings Using WMM QoS for Wireless Multimedia Applications Using WMM for Wireless Multimedia ApplicationsQuality of Service To create a QoS policy for applications and online games Configuring QoS for Internet AccessQoS for Applications and Online Gaming Click Setup QoS Rule and then click Add Priority Rule QoS for a Router LAN PortQoS for a MAC Address Editing or Deleting an Existing QoS Policy Click Setup QoS RuleChanging the MTU Size Overview of Home and Small Office Networking Technologies Common MTU SizesAssessing Your Speed Requirements Theoretical Transfer Time for 1 Gigabyte Network Connection Theoretical Raw Transfer TimeUsing Network Monitoring Tools Using Network Monitoring ToolsViewing Wireless Router Status Information Wireless Router Status FieldsDhcp Click Connection Status to display the connection status Connection Status Settings Router StatisticsViewing a List of Attached Devices Rx B/sDo not interrupt the reboot process Managing the Configuration FileBacking Up and Restoring the Configuration Updating the Router Firmware Erasing the ConfigurationChecking for New Firmware in the Router Upgrade Screen Using Network Monitoring Tools Updating Manually to New Router Firmware Select the Turn Remote Management On check box Enabling Remote Management AccessTo configure your router for remote management Using Network Monitoring Tools Traffic Meter To monitor traffic on your router, do the followingUsing Network Monitoring Tools Be sure to restart your network in this sequence TroubleshootingQuick Tips Check the Test light to verify correct router operation Troubleshooting Basic FunctionsMake sure that the Ethernet cables are securely plugged Power light stays amber Power light is not onPower light blinks green slowly and continuously Internet light stays amberLogin Problems Internet or LAN port lights are not onChecking the Internet Service Connection Obtaining an Internet IP AddressTroubleshooting PPPoE Troubleshooting Internet BrowsingTroubleshooting Your Network Using the Ping Utility Testing the LAN Path to Your RouterTesting the Path from Your Computer to a Remote Device Request timed outProblems with Date and Time Problems with Wireless Adapter ConnectionsRestoring the Default Configuration and Password These procedures erase all current configuration settingsAppendix a Technical Specifications Default Configuration SettingsWNR1000v3h2 Router Default Configuration Settings Wireless Communication General Specifications WNR1000v3h2 Router General SpecificationsReference Documents Appendix B Related DocumentsRegulatory Compliance Information FCC Requirements for Operation in the United StatesEdoc in Languages of the European Community Europe EU Declaration of ConformityFCC Caution Pertinentes de la directive 1999/5/CE Interference Reduction Table Interference Reduction TableIndex IndexIndex PIN 32, 34 ping 54 Setup Manual
Top Page Image Contents