NETGEAR WNR1000v3h2 manual Restoring the Default Configuration and Password

Page 100

N150 Wireless Router User Manual

•Is your router’s wireless radio enabled? See Viewing Advanced Wireless Settings on page 29.

•Is your router’s SSID broadcast enabled? See Viewing Advanced Wireless Settings on page 29.

•Is your router set to a wireless standard that is not supported by your wireless adapter? Check the Mode setting as described in Viewing and Configuring Basic Internet Settings on page 11.

If your wireless network appears, but the signal strength is weak, check these conditions:

•Is your router too far from your adapter, or too close? Place the computer that has the adapter near the router, but at least 6 feet away, and see whether the signal strength improves.

•Is your wireless signal obstructed by objects between the router and your adapter? See Optimizing Wireless Performance on page 67.

Restoring the Default Configuration and Password

This section explains how to restore the factory default configuration settings that reset the router’s user name to admin, the password to password, and the IP address to 192.168.1.1.

WARNING!

These procedures erase all current configuration settings.

You can erase the current configuration and restore factory defaults in two ways:

•Use the Erase function of the router. To use the Erase function, see Erasing the Configuration on page 84.

•Use the restore factory settings button on the rear panel of the router. Use this method for cases when the administration password or IP address is not known.

To use the restore settings button:

1.Locate the restore factory settings button on the rear panel of the router.

2.Use a sharp object such as a pen or a paper clip to press and hold the restore factory settings button for about 5 seconds, until the Power light begins to blink.

3.Release the restore factory settings button, and wait for the router to restart, and for the Power light to stop blinking and become solid green.

The factory default settings will be restored so that you can access the router from your Web browser using the factory defaults.

If the wireless router fails to restart, or the Power light continues to blink or turns solid amber, the unit might be defective. If the error persists, you might have a hardware problem and should contact Technical Support at http://www.netgear.com/support.

100 Chapter 7: Troubleshooting

Page 99 Page 101
Image 100
Page 99 Page 101
Contents N150 Wireless Router WNR1000v3h2 Technical Support TrademarksStatement of Conditions Revision HistoryTable of Contents Customizing Your Network Settings Troubleshooting Using the Setup Manual Configuring Basic ConnectivityLogging In To Your Wireless Router Configuring Basic Connectivity Selecting a Language for Your Screen Display Configuring Basic Connectivity Viewing and Configuring Basic Internet Settings Configuring Your Internet Settings Using the Setup WizardYour Internet Connection Does Not Require a Login No login required Your Internet Connection Does Require a Login Login required Configuring Basic Connectivity Setting Up and Testing Basic Wireless Connectivity Configuring Basic Connectivity Click Setup Access List Safeguarding Your Network Safeguarding Your NetworkChoosing Appropriate Wireless Security To configure the wireless network, you can Wireless Security Options Other Features That Enhance SecurityRecording Basic Wireless Settings Setup Information If WEP Authentication is used, circle one Shared Key or AutoChanging Wireless Security Settings Viewing Basic Wireless SettingsSafeguarding Your Network Configuring WEP Wireless Security Safeguarding Your Network Configuring WPA-PSK and WPA2-PSK Wireless Security Viewing Advanced Wireless Settings Using Push N Connect Wi-Fi Protected Setup Push Button Configuration Using the Physical Push ButtonUsing the Router’s Security PIN Security PIN EntryConfiguring the WPS Settings Using the Wireless Client’s Security PINAdding Additional WPS-Enabled Clients Restricting Wireless Access by MAC Address Adding Additional Non-WPS-Enabled ClientsSelect the Turn Access Control On check box Adding Guest Networks To add a guest network, do the followingChanging the Administrator Password Backing Up Your Configuration Understanding Your Firewall Blocking Access to Internet Sites Content Filtering OverviewRestricting Access From Your Network Blocking Access to Internet Services To block access to Internet services Blocking Services by IP Address Range Scheduling BlockingViewing Logs of Web Access or Attempted Web Access Log Entry DescriptionsConfiguring E-mail Alert and Web Access Log Notifications Setting the Time Zone Using the LAN IP Setup Options Customizing Your Network SettingsConfiguring a Device Name Configuring LAN TCP/IP Setup ParametersUsing the Router as a Dhcp Server Using Address ReservationUsing a Dynamic DNS Service To reserve an IP addressTo edit or delete a reserved address entry Click Edit or DeleteTo configure for a Dynamic DNS service Configuring the WAN Setup OptionsSelect the Use a Dynamic DNS Service check box Setting Up a Default DMZ Server Disabling Port Scan and DoS ProtectionConfiguring Static Routes Setting the MTU SizeConfiguring NAT Filtering Responding to a Ping on the Internet WAN PortTo add or edit a static route Customizing Your Network Settings Fine-Tuning Your Network Allowing Inbound Connections to Your NetworkFine-Tuning Your Network How Port Triggering Changes the Communication Process Web server then sends this reply message to your routerHow Port Forwarding Changes the Communication Process Configuring Port Forwarding to Local Servers How Port Forwarding Differs from Port TriggeringAdding a Custom Service To configure port forwarding to a local serverClick Edit Service or Delete Service to make changes Editing or Deleting a Port Forwarding EntryApplication Example Making a Local Web Server Public To edit or delete a port forwarding entryConfiguring Port Triggering Clear the Disable Port Triggering check box Using Universal Plug and Play To turn on Universal Plug and PlayOptimizing Wireless Performance Choose your settings Identify critical wireless linksReduce interference Quality of Service Using WMM for Wireless Multimedia ApplicationsUsing WMM QoS for Wireless Multimedia Applications QoS for Applications and Online Gaming Configuring QoS for Internet AccessTo create a QoS policy for applications and online games Click Setup QoS Rule and then click Add Priority Rule QoS for a Router LAN PortQoS for a MAC Address Changing the MTU Size Click Setup QoS RuleEditing or Deleting an Existing QoS Policy Overview of Home and Small Office Networking Technologies Common MTU SizesAssessing Your Speed Requirements Theoretical Transfer Time for 1 Gigabyte Network Connection Theoretical Raw Transfer TimeUsing Network Monitoring Tools Using Network Monitoring ToolsViewing Wireless Router Status Information Wireless Router Status FieldsDhcp Click Connection Status to display the connection status Connection Status Settings Router StatisticsViewing a List of Attached Devices Rx B/sBacking Up and Restoring the Configuration Managing the Configuration FileDo not interrupt the reboot process Checking for New Firmware in the Router Upgrade Screen Erasing the ConfigurationUpdating the Router Firmware Using Network Monitoring Tools Updating Manually to New Router Firmware To configure your router for remote management Enabling Remote Management AccessSelect the Turn Remote Management On check box Using Network Monitoring Tools Traffic Meter To monitor traffic on your router, do the followingUsing Network Monitoring Tools Quick Tips TroubleshootingBe sure to restart your network in this sequence Make sure that the Ethernet cables are securely plugged Troubleshooting Basic FunctionsCheck the Test light to verify correct router operation Power light is not on Power light blinks green slowly and continuouslyPower light stays amber Internet light stays amberLogin Problems Internet or LAN port lights are not onChecking the Internet Service Connection Obtaining an Internet IP AddressTroubleshooting PPPoE Troubleshooting Internet BrowsingTroubleshooting Your Network Using the Ping Utility Testing the LAN Path to Your RouterTesting the Path from Your Computer to a Remote Device Request timed outProblems with Date and Time Problems with Wireless Adapter ConnectionsRestoring the Default Configuration and Password These procedures erase all current configuration settingsWNR1000v3h2 Router Default Configuration Settings Default Configuration SettingsAppendix a Technical Specifications Wireless Communication General Specifications WNR1000v3h2 Router General SpecificationsReference Documents Appendix B Related DocumentsRegulatory Compliance Information FCC Requirements for Operation in the United StatesFCC Caution Europe EU Declaration of ConformityEdoc in Languages of the European Community Pertinentes de la directive 1999/5/CE Interference Reduction Table Interference Reduction TableIndex IndexIndex PIN 32, 34 ping 54 Setup Manual
Top Page Image Contents