NETGEAR MBRN3000-100NAS user manual Using Static Routes, Static Route Example

Page 54

Mobile Broadband Wireless-N Router MBRN3000

6.If your dynamic DNS provider allows the use of wildcards in resolving your URL, you can select the Use wildcards check box to activate this feature.

For example, the wildcard feature will cause *.yourhost.dyndns.org to be aliased to the same IP address as yourhost.dyndns.org.

7.Click Apply to save your configuration.

Using Static Routes

Static routes provide additional routing information to your router. Under normal circumstances, the router has adequate routing information after it has been configured for Internet access, and you do not need to configure additional static routes. You must configure static routes only for unusual cases such as multiple routers or multiple IP subnets located on your network.

Static Route Example

As an example of when a static route is needed, consider the following case:

Your primary Internet access is through a cable modem to an ISP.

You have an ISDN router on your home network for connecting to the company where you are employed. This router’s address on your LAN is 192.168.0.100.

Your company’s network is 134.177.0.0.

When you first configured your router, two implicit static routes were created. A default route was created with your ISP as the router, and a second static route was created to your local network for all 192.168.0.x addresses. With this configuration, if you attempt to access a device on the 134.177.0.0 network, your router forwards your request to the ISP. The ISP forwards your request to the company where you are employed, and the request is likely to be denied by the company’s firewall.

In this case you must define a static route, telling your router that 134.177.0.0 should be accessed through the ISDN router at 192.168.0.100.

In this example:

The Destination IP Address and IP Subnet Mask fields specify that this static route applies to all 134.177.x.x addresses.

The Gateway IP Address fields specify that all traffic for these addresses should be forwarded to the ISDN router at 192.168.0.100.

In the Metric field, a value of 1 will work since the ISDN router is on the LAN.

This represents the number of routers between your network and the destination. This is a direct connection, so it is set to 1.

Private is selected only as a precautionary security measure in case RIP is activated.

Chapter 5: Advanced 53

Image 54
Contents Mobile Broadband Wireless-N Router MBRN3000 Mobile Broadband Wireless-N Router MBRN3000 Statement of Conditions Technical Support NETGEAR, IncTrademarks Revision History Publication Part NumberTable of Contents Advanced Factory Default Settings Technical Specifications Hardware Features Router Front PanelUSB LAN WPSRouter Back Panel Router LabelUsing the Router Stand Logging In to Your RouterTo log in to the router Accessing the Setup Wizard After Installation Manually Configuring Your Internet SettingsTo manually configure your Internet settings Fields and Checkboxes Description Wireless Network Configuration Planning Your Wireless NetworkWireless Placement and Range Guidelines Wireless Security OptionsManually Configuring Your Wireless Settings Wireless SecurityTo view or manually configure the wireless settings Settings DescriptionWireless Guest Networks To configure a wireless guest networkConfiguring WEP To configure WEP data encryptionUsing Push N Connect WPS to Configure Your Wireless Network Configuring WPA, WPA2, or WPA + WPA2To configure WPA or WPA2 in the router WPS Button To use the router WPS button to add a WPS clientWPS PIN Entry To use a PIN to add a WPS clientAdding Wireless Computers that Do Not Support WPS Changing Wireless Settings for the NetworkProtecting Access to Your Mobile Broadband Wireless-N Router Changing the Built-In PasswordChanging the Administrator Login Time-out Blocking Sites and KeywordsKeyword Result XXXBlocking Services Setting Your Time Zone SchedulingScheduling Firewall Services Live Parental ControlsWeb-based GUI Backing Up, Restoring, or Erasing Your Settings Backing Up the Configuration to a FileTo erase the configuration Restoring the Configuration from a FileErasing the Configuration Upgrading the Router FirmwareMobile Broadband Wireless-N Router MBRN3000 Hsdpa Router StatusField Description ImsiWireless Settings DhcpShowing Statistics Connection Status Viewing Attached Devices Viewing, Selecting, and Saving Logged InformationExamples of Log Messages Field or button DescriptionActivation and Administration Enabling Security Event E-mail NotificationRunning Diagnostic Utilities and Rebooting the Router To receive alerts and logs by e-mailSelect the Turn E-mail Notification On check box Enabling Remote Management ScanConfiguring Remote Management Http//134.177.0.1238080Advanced Wireless Settings AdvancedWireless Station Access Control Turning off wireless connectivity completelyHiding your wireless network name Ssid Restricting Access by MAC Address To restrict access based on MAC addressesTo set up port forwarding Port Forwarding and Port TriggeringPort Forwarding To view or change the WAN Setup WAN SetupTo set up port triggering Port TriggeringSetting Up a Default DMZ Server Setting DescriptionLAN IP Settings To assign a computer or server to be a default DMZ serverTo view or change the LAN IP Setup Dhcp Settings LAN TCP/IPTo edit or delete a reserved address entry Reserved IP AddressesTo reserve an IP address Click Edit or DeleteConfiguring Dynamic DNS Select the Use a Dynamic DNS Service check boxDynamic DNS Using Static Routes Static Route ExampleTo configure static routes Universal Plug and Play UPnPTraffic Meter To monitor traffic on your router Troubleshooting Basic FunctioningTroubleshooting Access to the Router Main Menu ActionTroubleshooting the ISP Connection Connecting to the InternetTesting the LAN Path to Your Router Troubleshooting a TCP/IP Network Using the Ping UtilityTroubleshooting Internet Browsing To ping the router from a PC running Windows 95 or laterTesting the Path from Your Computer to a Remote Device Request timed outRestoring the Default Configuration and Password Problems with Date and TimeLAN IP Factory Default SettingsFeature Default Behavior DMZList All wireless stations allowed NetgearTCP/IP, Dhcp Technical SpecificationsTechnical Specifications WAN USBRelated Documents Notification of Compliance Regulatory Compliance InformationΣυμμορφωνεται Προσ ΤΙΣ Ουσιωδεισ Απαιτησεισ ΚΑΙ ΤΙΣ Λοιπεσ Σχετικεσ Διαταξεισ ΤΗΣ Οδηγιασ 1999/5/ΕΚFCC Requirements for Operation in the United States FCC Information to UserFCC Caution Voluntary Control Council for Interference Vcci StatementIndex Index