APC AP9607 manual Interface Expander, Specification

Page 36

Specifications continued

Product

The following table shows the product specifications for the

specifications:

Interface Expander.

 

Table 7

 

 

 

Item

Specification

 

 

 

 

Physical

 

 

 

 

 

Size (H × W × D):

4.0 × 4.0 × 1.5 in

 

 

(10.2 × 10.2 × 3.8 cm)

 

 

 

 

Weight:

0.3 lb (0.136 kg)

 

 

 

 

Shipping weight:

0.7 lb (0.318 kg)

 

 

 

 

Environmental

 

 

 

 

 

Elevation (above MSL):

 

 

Operating

0 to 10,000 ft (0 to 3000 m)

 

Storage

0 to 50,000 ft (0 to 15 000 m)

 

 

 

 

Temperature:

 

 

Operating

32 to 104°F (0 to 40°C)

 

Storage

5 to 113°F (-15 to 45°C)

 

 

 

 

Operating Humidity:

0 to 95%, non-condensing

 

 

 

 

Approvals

 

 

 

 

 

EMC verification:

FCC/DOC Class B, EN 50022,

 

 

EN50082-1

 

 

 

 

Other:

CE, C-Tick (AS/NZS 3538)

 

 

 

 

 

 

32

Page 35 Page 37
Image 36
Page 35 Page 37
Contents
Interface Expander Thank You Contents Connection procedure Connecting the Interface Expander Introduction On next Hardware Software Requirements By the Interface Expander. When ordering a cable, provide Part NumberProduct Description Status Description Simple Signaling Smart Signaling Key ConceptsCommunication Types PowerChute plus, configured for smart signaling, to moni UPS can provide simple signaling, we strongly recommendPowerChute plus Expander use simple signaling with PowerChute orSignaling. Use either one of these procedures UPS and continue with the installation, includingReboot of the system Run PowerChute plus and connect to the UPSInterface Expander generates a Low Battery signal Less of whether the UPS is on battery. The InterfaceExpander generates a Low Battery signal under certain Other conditions according to the configured shutdownKey Concepts Multiple SmartSlot Installation Multiple SmartSlot Installation Multiple SmartSlot Installation Installation Orient the Interface Expander to fit the accessory Slot. Slide the Interface Expander all the way intoSlot until the front panel is flush with the back Panel of the UPS or deviceConnecting to Protected Devices Described in Connection procedure on Configuring the Interface Expander Some versions of PowerChute plus do not support Con Firmed shutdown mode when set up for simple signalingPowerChute plus installation directory. To find out Whether your version of PowerChute plus supports ConIf power returns before any connected server has signaled UPS before all connected servers have signaled shutUPS battery is exhausted, shutting down the UPS after Low Battery Signal Time has elapsedExpander allows the UPS to run on battery until utility Power is restored, or until the battery is exhausted. IfInterface Expander detects a UPS Low Battery condition, it Equal to the Low Battery Signal Time and then shuts downTesting Interface Expander Warranty Information Claims by third parties, or otherwise. This warranty gives Purpose. Some jurisdictions do not permit limitation orExclusion of implied warranties therefore, the aforesaid Specifically, APC is not liable for any costs, such as lostTroubleshooting Problem Possible Cause Solution For problems not covered in the troubleshooting chart see Troubleshooting on page 26, or if the problemPersists, follow this procedure Lem. a technician will help solve the problem overLife-Support Policy Specifications Assignments Specification Interface ExpanderIndex Index Y, Z Page Application of Coun Cil Directives Standards to WhichConformity is DeclaredW. a p c c . c o m