APC AP9607 manual Index

Page 37

Index

A

Accessories

placement of, 12

Advanced port

using with Confirmed shutdown mode, 21

AppleShare server cable, 4

B

Basic port

description, 5

pin assignments, 3031 Behavior of Confirmed mode, 21

C

Cables, choosing additional, 4 Call-UPS II, priority in multiple

SmartSlot device installation, 12

Checking operation, 23 Choosing cables, 4 Configuration DIP switches, 5 Configuring PowerChute plus for

simple signaling, 9 Configuring the Interface

Expander, 1923 Confirmed shutdown mode

behavior, 21 description, 20

PowerChute plus support for, 20

Connecting the Interface Expander figure, 18

Connecting to Protected Devices, 1718

Connection procedure, 17

D, E

Daisy chains, 14

DIP switches behavior, 19 description, 5

Expansion Chassis, daisy chaining with, 14

Extension cables, 4

F, G, H

Features of the Interface Expander, 2 Front panel, 5

Hardware and software requirements, 3

Hospital-grade wiring devices, 29 Humidity

safety warning, 4

I

IBM server cable, 4 Installation, 15 Installation in the APC Triple

Chassis, 13 Installation in the Symmetra

PowerArray, 14 Installation procedure, 1516 Interface Expander

priority in multiple SmartSlot device

installation, 12 Interface Expander panel, 5 Interface Extension Cable, 4 Interface kits, 4 Introduction to the Interface

Expander, 14

Isolated Extension Cable, 4

J, K, L

Key Concepts, 711

Leakage current protection, 29 LED status, 6

33

Image 37
Contents Interface Expander Thank You Contents Connection procedure Connecting the Interface Expander Introduction On next Hardware Software Requirements Part Number By the Interface Expander. When ordering a cable, provideProduct Description Status Description Key Concepts Simple Signaling Smart SignalingCommunication Types UPS can provide simple signaling, we strongly recommend PowerChute plus, configured for smart signaling, to moniPowerChute plus Expander use simple signaling with PowerChute orUPS and continue with the installation, including Signaling. Use either one of these proceduresReboot of the system Run PowerChute plus and connect to the UPSLess of whether the UPS is on battery. The Interface Interface Expander generates a Low Battery signalExpander generates a Low Battery signal under certain Other conditions according to the configured shutdownKey Concepts Multiple SmartSlot Installation Multiple SmartSlot Installation Multiple SmartSlot Installation Installation Slot. Slide the Interface Expander all the way into Orient the Interface Expander to fit the accessorySlot until the front panel is flush with the back Panel of the UPS or deviceConnecting to Protected Devices Described in Connection procedure on Configuring the Interface Expander Firmed shutdown mode when set up for simple signaling Some versions of PowerChute plus do not support ConPowerChute plus installation directory. To find out Whether your version of PowerChute plus supports ConUPS before all connected servers have signaled shut If power returns before any connected server has signaledUPS battery is exhausted, shutting down the UPS after Low Battery Signal Time has elapsedPower is restored, or until the battery is exhausted. If Expander allows the UPS to run on battery until utilityInterface Expander detects a UPS Low Battery condition, it Equal to the Low Battery Signal Time and then shuts downTesting Interface Expander Warranty Information Purpose. Some jurisdictions do not permit limitation or Claims by third parties, or otherwise. This warranty givesExclusion of implied warranties therefore, the aforesaid Specifically, APC is not liable for any costs, such as lostTroubleshooting Problem Possible Cause Solution Troubleshooting on page 26, or if the problem For problems not covered in the troubleshooting chart seePersists, follow this procedure Lem. a technician will help solve the problem overLife-Support Policy Specifications Assignments Interface Expander SpecificationIndex Index Y, Z Page Cil Directives Standards to Which Application of CounConformity is DeclaredW. a p c c . c o m