3Com NETBuilder II manual Chapter Installation, Before Installing the Hssi Module

Page 5

Chapter 1

Installation

This chapter describes how to install the HSSI module into the NETBuilder II® base system. The HSSI module provides a single serial interface for a WAN connection in the NETBuilder II base system. It supports transmission rates up to OC1, including E3, T3, and sub-rates.

NOTE: The HSSI module must be used with NETBuilder II HSSI and Single-Mode FDDI Software 6.2. For information about the software, see the NETBuilder II HSSI and Single- Mode FDDI Software 6.2 Release Notes.

For information about the HSSI module components, refer to Appendix A, “HSSI Module Components.”

Before Installing the HSSI Module

Before you install the HSSI module into the NETBuilder II base system, follow these steps:

1.Observe appropriate ESD precautions.

Electrostatic discharge (ESD) can damage circuit board components. Failures resulting from ESD may not be covered under your warranty. To prevent this, follow these handling procedures:

Keep the HSSI module in its antistatic shielded bag until you are ready to install it.

Do not touch pins, leads, or solder connections on the board.

Handle the board by the edges only.

Store or ship the HSSI module in static-protective packaging.

Observe proper grounding techniques when handling the HSSI module: Use a foot strap and grounded mat, or wear a grounded static discharge wrist strap.

2.Inspect the HSSI module for shipping damage.

If you find any damage, contact the shipping company to file a report. If the assembly must be returned to your network supplier, ship it in its original shipping carton. If the original carton was damaged in shipment, repack the system in a carton that provides equivalent protection.

Image 5
Contents Member of the NETBuilder family NETBuilder II Hssi Module Installation Guide3Com Corporation Bayfront Plaza Santa Clara California Before You Begin How to Use This GuideConventions If you are looking for Turn toSpecial Messages Before Installing the Hssi Module Chapter InstallationObserve appropriate ESD precautions Inspect the Hssi module for shipping damageVerify that you have received all the contents Select an I/O slot in which to install the Hssi module Installing the Hssi ModuleHand tighten the captive screws. Do not use a screwdriver Lock the board in the slotCabling the Hssi Module for Network Connection Hotswap Internal Loopback testTroubleshooting Startup Problems Chapter Troubleshooting and MaintenancePreventive Maintenance Maintaining the Hssi ModuleReplacing the Hssi Module LED Normal Color Indicates Behavior Appendix a Hssi Module ComponentsLEDs Location Connector Number of pins Purpose ConnectorsSpecifications Attribute DescriptionType Y Type 3 to access the MAC address of the Hssi moduleAppendix B Displaying the MAC Address Displaying the MAC Address On-line Technical Services Automated Fax Service3Com Product Information Service Appendix C Technical SupportAdditional Technical Support Services Warranty Information3Com Documentation on CD-ROM Adapter-Specific Bulletin Board System BBSReturning Products for Repair Before Contacting Your Network SupplierAdditional 3Com Support Services Preparing Your Equipment for Shipment Equipment Warranties and Repair ServicesEurope and Africa Technical Support

NETBuilder II specifications

The 3Com NETBuilder II is a robust networking solution designed to meet the requirements of enterprise-level organizations. Launched in the late 1990s, this platform was celebrated for its advanced features and high-performance capabilities. As a modular, multi-layer switch, it provides flexible configurations that allow businesses to scale their networks according to changing demands.

One of the standout features of the NETBuilder II is its support for both Layer 2 and Layer 3 switching. This dual functionality enables efficient data handling at various layers of the OSI model, allowing for improved network efficiency and reduced latency. With support for both Ethernet and Fast Ethernet, the device delivers high-speed connectivity to enhance data transmission rates across the network.

The NETBuilder II is equipped with a modular architecture, offering interchangeable line cards that facilitate customization according to specific network needs. This design allows organizations to start with basic configurations and expand their systems by adding additional modules as required. This modularity is particularly beneficial for organizations anticipating growth or changes in their networking requirements.

Another essential technology integrated into the NETBuilder II is Virtual LAN (VLAN) support. VLANs provide the ability to segment network traffic effectively, which enhances security and optimizes performance. By segregating traffic, organizations can minimize broadcast domains and improve overall network efficiency while maintaining strict control over data access.

Furthermore, the device is designed with advanced routing capabilities, supporting protocols like RIP, OSPF, and PIM. These routing features are crucial for organizations that need to manage complex data flows and ensure efficient path selection for data packets, ultimately contributing to a more reliable network infrastructure.

In terms of management, the NETBuilder II offers support for SNMP, simplifying the monitoring and management of network devices. This feature enables IT administrators to track performance, troubleshoot issues in real-time, and maintain optimal operational conditions.

The 3Com NETBuilder II also boasts a solid reputation for reliability and durability, making it suitable for mission-critical applications in various industries. Its robust nature ensures continuous uptime and service reliability, which is paramount in today's increasingly connected business landscape.

Overall, the 3Com NETBuilder II is an influential piece of networking technology. Its combination of modularity, advanced routing features, VLAN support, and high-performance capabilities make it a key asset for enterprises looking to build a scalable, efficient, and reliable network infrastructure.