|
|
|
|
|
|
|
| Features in |
|
|
| 12 | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR | Module | Level | Description | AR400 | AR7x5 | AR7x0S | Rapier i |
| Rapier w | AT8800- |
| x90048- | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00012871 | TTY | 2 | Unexpected characters could appear on the terminal emulator display | Y | Y | Y | Y |
| Y | Y | Y |
| Y | Y | Y | Y |
|
|
| when the column size was set greater than 80 and the user edited a |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| command that spanned more than one line of the display. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00013597 | DVMRP, | 2 | If a frame relay interface was configured as a DVMRP interface, then the | Y | Y | Y | Y |
| Y | - | - |
| - | - | - | - |
| Frame Relay |
| DLC value was not correctly generated in output of the command show |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| config dynam or in the configuration script generated by the command |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| create config. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00013660 | Core, SNMP | 2 | Previously, SNMP returned an incorrect product ID number for | - | - | Y | - |
| - | - | - |
| - | - | - | - |
|
|
| routers. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. The value of the sysObjectID object is now 80 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| for |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00013735 | LACP, | 2 | When moving ports from an | - | - | - | - |
| - | - | - |
| - | Y | Y | - |
| Switching |
| configured trunk, ports were incorrectly set in an STP blocking state. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Therefore, traffic would not flow over the trunk. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Note: When you move ports from an |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| configured trunk, you must delete the ports from LACP. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00013763 | OSPF | 2 | If the obsolete command set ospf rip=both was entered, the router or | Y | Y | Y | Y |
| Y | Y | Y |
| Y | Y | Y | Y |
|
|
| switch correctly automatically replaced it with the following two |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| commands in the dynamic configuration: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| add ospf redistribute protcol=rip |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| set ospf rip=export |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| However, if the command create config was used to save the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| configuration, after system |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| the command add ospf redistribute protocol=rip. This meant that OSPF |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| stopped redistributing RIP routes after a reboot. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Version