|
|
|
|
|
|
|
| Features in |
|
|
| 52 | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR | Module | Level |
| Description | AR400 | AR7x5 | AR7x0S |
| Rapier i | AT8800- |
| x90048- | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
CR00016228 | QoS | 3 | If a QoS policy uses the same classifier more than once, the router or switch now | Y | Y | Y |
| Y | Y | Y |
| Y | Y | Y | Y | |
|
|
| displays a warning message. You should not use a classifier more than once in a |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| policy because the operation of such policies is unpredictable. |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
CR00016463 | DHCPv6 | 3 | For the command create dhcp6 range, DHCPv6 now checks that the specified | Y | Y | Y |
| Y | Y | - |
| - | Y | Y | Y | |
|
|
| address or prefix range is valid for the specified type of range. |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| Valid options are: |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| ■ |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| This is a range of addresses for address assignment (type=normal or |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| type=temporary). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ■ | address/prefixLen (e.g. 3ffe:1:2:3:4:5::/96) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This is a range of addresses for address assignment (type=normal or |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| type=temporary). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ■ |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| This is a range of prefixes for prefix assignment (type=pd). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
CR00016799 | Core | 3 | For revision M1 of AR770S routers, the | - | - | Y |
| - | - | - |
| - | - | - | - | |
|
|
| volt rail was too high. This caused power supply monitoring false alarms. |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| To check the router revision, use the command show system and check the |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| “Rev” entry underneath the time and date. |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| This issue has been |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
CR00017008 | Core | 3 | Revisions | - | Y | - |
| - | - | - |
| - | - | - | - | |
|
|
| Supplies. Therefore, for these routers, RPS monitoring information has been |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| removed from output of the command show system, and it is no longer |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| possible to use the command set sys rpsmonitor. |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Version