|
|
|
|
|
|
|
| Features in |
|
|
| 17 | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR | Module | Level | Description | AR400 | AR7x5 | AR7x0S | Rapier i |
| Rapier w | AT8800- |
| x90048- | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00017226 | IPsec | 2 | If an IPsec tunnel with no encryption (NULL) was negotiated in AlliedWare | Y | Y | Y | Y |
| Y | Y | - |
| - | - | - | - |
|
|
| over |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| checksum. This means that some vendors may have discarded packets sent |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| by the AlliedWare peer over such a tunnel. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Note the null encryption is useful for debugging the traffic over an IPsec |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| tunnel and should not be used in a working IPsec solution. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00017227 | IPsec | 2 | An IPSec checksum recalculation error occurred with UDP traffic when the | Y | Y | Y | Y |
| Y | Y | - |
| - | - | - | - |
|
|
| ESP encapsulation was added. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00017255 | Switching | 2 | Previously, trunk members were given the STP state in hardware of port 1, | - | - | - | Y |
| Y | Y | Y |
| Y | - | - | - |
|
|
| instead of having the STP state of the lead port in the trunk. The software |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| state (as displayed with the command show stp port) was correct. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00017256 | Switching | 2 | When using | - | - | - | - |
| - | - | - |
| - | Y | Y | - |
|
|
| hardware switching would stop for all |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| VLAN, if one of the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| administratively down state. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00017337 | Switching | 2 | It was possible to set up a classifier that matched MPLS frames at layer 2, | - | - | - | - |
| - | - | - |
| - | Y | Y | - |
|
|
| but the switch would not correctly match these MPLS frames against the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| classifier. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. The switch now correctly matches MPLS |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| frames against such a classifier. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Version