|
|
|
|
|
|
| Features in |
|
|
| 50 | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR | Module | Level | Description | AR400 | AR7x5 | AR7x0S |
| Rapier i | AT8800- |
| x90048- | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00011629 | PIM, PIM6, | 3 | Previously, the switch’s count of PIM4 and PIM6 bad Bootstrap Messages (BSMs) | - | - | - |
| - | - | - |
| - | Y | Y | - |
| ECMP |
| could be high, because the switch forwarded BSMs over interfaces that |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| contained an Equal Cost Multipath (ECMP) route to the receiving interface. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. BSMs are no longer forwarded via all interfaces |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| contained in an ECMP group, but only via one interface in the group. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00012495 | IGMP | 3 | When an IGMP filter was destroyed, switch ports that used the filter did not have | Y | Y | Y |
| Y | Y | Y |
| Y | Y | Y | Y |
|
|
| their IGMP filter setting returned to “None”. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00014324 | PPP | 3 | The interface MIB ifInOctets and ifOutOctets counters displayed by the show | Y | Y | Y |
| Y | Y | - |
| - | Y | Y | Y |
|
|
| ppp counter command incorrectly included the lower layer framing octets and |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| were 5 octets per frame greater than they should have been. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00014919 | QoS, | 3 | DHCP snooping accepted a minimum of one new client per QoS flow group, | - | - | - |
| Y | Y | Y |
| Y | Y | Y | - |
| DHCP |
| instead of a minimum of one new client per port. This meant that DHCP |
|
|
|
|
|
|
|
|
|
|
|
|
| snooping |
| snooping sometimes did not respect the lease limit (maxlease) on a port. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00015092 | ATM | 3 | Previously, the information output by the “?” help for the ATM channel pcr | Y | - | - |
| - | - | - |
| - | - | - | - |
|
|
| parameter was incorrect. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. The “?” help now displays: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| required - decimal in the range |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| If you enter a value larger than the maximum PCR allowed on a specific physical |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| interface, the router now displays the following message for ADSL: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| The PCR supplied was too large, the maximum is 1024 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| and the following message for SHDSL: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| The PCR supplied was too large, the maximum is 4608 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Version