Kenwood TS-870S instruction manual Setting Baud Rate bps Stop Bits

Page 33

5 MENU SETUP

Menu

Menu Item

 

 

Function

 

Selections

Default

Page

No.

 

 

 

Ref.

 

 

 

 

 

 

 

48

PF.KEY.LL

Programmable Function button (lower left)

OFF, 00 ~ 73

72 (FINE)

63

49

CH.SHIFT

Fixed (OFF) or tunable (ON) memory channel

OFF/ON

OFF

56

 

 

frequencies

 

 

 

 

50

DIMMER

Display brightness (controls LCD and LED brightness)

L/ H

H

65

 

 

L: Low

 

 

 

 

 

 

H: High

 

 

 

 

51

LINEAR

Linear amplifier relay response time

OFF/ 1/ 2

1

5

 

 

• 1: Fast, 2: Slow

 

 

 

 

52

1M/500k

1 MHz button frequency step

 

100/ 500/ 1000 kHz

1000 kHz

20

53

EXT RX

External RX jack (EXT RX ANT) enable for external

OFF/ON

OFF

2

 

 

receiver

 

 

 

 

 

54

TRNSFER

Data transfer function enable

 

OFF/ON

OFF

66

55

DIRECT

Method of receiving transferred data

OFF/ON

OFF

66

 

 

• OFF: Transfer to Quick memory

 

 

 

 

 

ON:

Transfer directly to VFO

 

 

 

 

 

 

 

 

 

 

56

COM.RATE

Communication parameters for COM connector

12 1/ 24 1/ 48 1/ 48 2/

96 1

50

 

 

Setting

Baud Rate (bps)

Stop Bits

96 1/ 192 1/ 384 1/

 

 

 

 

 

12 1

1200

1

576 1

 

 

 

 

 

24 1

2400

1

Note: To reliably use the

 

 

 

 

 

48 1

4800

1

38400 or 57600 bps

 

 

 

 

 

transfer rates, the serial

 

 

 

 

 

48 2

4800

2

 

 

 

 

 

port of your computer must

 

 

 

 

 

96 1

9600

1

support these high-speed

 

 

 

 

 

192 1

19200

1

communications

 

 

 

 

 

parameters.

 

 

 

 

 

384 1

38400

1

 

 

 

 

 

 

 

 

 

 

 

576 1

57600

1

 

 

 

 

 

 

 

 

 

57

SUB.TONE

Subaudible Tone frequency for FM mode

See page reference

88.5 Hz

39

58

SUB.TONE

Type of subtone

 

B/ C

C

39

 

 

B: Burst

 

 

 

 

 

 

C: Continuous

 

 

 

 

59

FM.BOOST

Low-frequency boost for FM receive mode

OFF/ON

OFF

60

FM WIDE

Wide band FM deviation enable

 

OFF/ON

ON

 

 

• OFF: Narrow (2.5 kHz)

 

 

 

 

 

 

• ON: Wide (5 kHz)

 

 

 

 

 

 

 

 

 

 

 

61

FM MIC

Microphone gain for FM mode

 

L/ H

L

38

 

 

L: Low

 

 

 

 

 

 

H: High

 

 

 

 

 

 

Note: Front Panel MIC gain control has no effect when using the

 

 

 

 

 

FM mode.

 

 

 

 

 

 

 

 

 

 

 

 

 

62

FSK.SHFT

FSK shift

 

 

170/ 200/ 425/ 850 Hz

170 Hz

40

63

MARK.POL

Key-down polarity for FSK

 

OFF/ON

OFF

40

 

 

OFF: Space

 

 

 

 

 

 

ON:

Mark

 

 

 

 

64

FSK.TONE

FSK tone

 

 

1275/ 2125 Hz

2125 Hz

40

65

PG.S.HOLD

Scan hold

 

OFF/ON

OFF

60

66

GRP.SCAN

Group Scan enable for memory channels

OFF/ON

OFF

61

 

 

• OFF: All-channel Scan

 

 

 

 

 

 

ON:

Group Scan

 

 

 

 

67

BSY.STOP

Busy Stop for Memory Scan

 

OFF/ON

ON

61

68

CAR.SCAN

Carrier-operated Scan Resume enable for

OFF/ON

OFF

61

 

 

Memory Scan

 

 

 

 

 

 

• OFF: Time-operated

 

 

 

 

 

 

• ON: Carrier-operated

 

 

 

 

 

 

 

 

 

 

 

 

 

27

Image 33
Contents TS-870S Applicable Model Writing Conventions FollowedKEY2 Power Cable Protection Power SourcesPower Lines CleaningContents Memory Features Rejecting InterferenceScan Optional Accessories MaintenanceInstalling Options Specifications AppendicesFeatures DSP Maximum SIGNAL/ Minimum NoiseSupplied Accessories IntroductionInstallation Antenna ConnectionTransmission Line MHz 14 MHz 30 MHz Installation DC Power Supply ConnectionGround Connection Lightning ProtectionAccessory Connections Front PanelRear Panel Rtty Equipment Rtty and ACC Computer Interface COMLinear Amplifier Remote Pin FunctionAccessory Equipment ACC Antenna Tuner ATSM-230 Station Monitor if OUT ANO GND PSQ Smet Pin No. Pin NamePKS PKDYour First QSO First QSO Getting Acquainted Front Panel6KEY Speed control @4QUICK Memo M.IN button@5QUICK Memo MR button Enter button @7Tuning controlLSB/USB button CW/ÐR buttonRX M.CH button #3BEAT Cancel button#5TX EQ. button #6FILTER LO/WIDTH and HI/SHIFT controls$4RIT/XIT control Microphone$7M.CH/VFO.CH control UP/DWN buttonsRear Panel 0AUTO Display1PROC 2MONI7SPLIT 5MENU8RIT 9TONE#3AT Tune #2ON AIR#4FSK #7M.SCRAdjusting Volume Switching Power ON/OFFAdjusting Squelch Operating BasicsSelecting Mode Operating Basics Equalizing VFO Frequencies A=BChanging Bands Quick Changes Fine TuningOperating Basics Changing Step SizesFront Panel Meter Operating Basics Direct Frequency EntryMeter on Transmitting Selecting Transmit PowerTransmit Carrier Level Microphone GainWhat is a MENU? Menu SetupMenu Access Temporary Menu ResettingMenu Setup Menu ConfigurationMenu Item Function Selections Default LO/WIDTH and HI/SHIFT controlsM.CH/VFO.CH control Setting Baud Rate bps Stop Bits Cross Reference for Menu Functions SSB Transmission CommunicatingSlow Scan TV/ Facsimile Sstv FrequenciesCW Transmission Switching TX/RX ManuallyCommunicating TX SIDETONE/ RX Pitch FrequencyCommunicating Semi BREAK-IN Setting Delay TimeFull BREAK-IN CW Reverse ReceiveCommunicating Electronic Keyer Function DefaultActivity Consult KEY Speed controlEmulation Options Multiple-Button FunctionsCW Message Playback Storing CW MessagesErasing CW Messages Inquiry Command DescriptionInquiry Functions To check an Inquiry function Press CH 3+CHPress CH 1+CH Function CommandsEmbedded Functions Serial Number OptionsOption d Leading Other Nines FM Repeater Operation FM TransmissionPress RX B or RX a Press RX a or RX BSelecting Subtone Frequency Continuous or Burst Subtones?Arrl 10-METER Band Plan AM Transmission Digital OperationRtty Frequency Shift Keying Mode Meaning ERROR-CHECKING Modes AMTOR/ PACKET/ PACTOR/ G-TOR/ CloverRtty Frequencies AmtorPacket Frequencies SPLIT-FREQUENCY OperationSatellite Operation Communicating TF-SET Transmit Frequency SETOperating Aids RIT Receive Incremental TuningReceiving AGC Automatic Gain ControlOperating Aids XIT Transmit Incremental TuningVOX VOICE-OPERATED Transmit Transmit InhibitOperating Aids Speech Processor SSB/AM Mode Transmit Sampling PointChanging Frequency While Transmitting Transmit MonitorTransmit Bandshift Changing Transmit BandwidthEqualizing Transmit Audio Microphone AGCAutomatic Mode Boundaries Automatic ModeUsing Automatic Mode Press MENU+Preset Bands for Internal Tuner Presetting Internal Tuner onlyAutomatic Antenna Tuner Internal TunerOperating Aids AT-300 External Tuner Optional Communication ParametersMenu No Baud Rate Stop Bits Rejecting Interference Slope Tuning SSB/AMDSP Tools If Shift CWRejecting Interference Beat Cancel SSB/AMAuto Notch SSB CW/FSK/FM Adaptive FiltersNoise Blanker Setting Spac TimeAIP Advanced Intercept Point AttenuatorConventional or Quick MEMORY? Memory FeaturesConventional Memory Memory Channel DataMemory Channel Recall Memory FeaturesSplit-Frequency Channels Quick Channel SearchMemory Channel Scroll Memory TransferTemporary Frequency Changes Memory \ VFO TransfersErasing Memory Channels Full ResetChannel to Channel Transfers ChannelProgrammable VFO Function Memory Features Storing Scan Limits in CHStoring Into Quick Memory Quick MemoryRecalling from Quick Memory Temporary Frequency ChangesProgram Scan ScanScan Hold Confirming START/END LimitsScan Memory ScanBusy Frequency Stop ALL-CHANNEL ScanMemory Channel Lockout Setting Scan SpeedSwitching ANT 1/ ANT Microprocessor ResetOperator Conveniences Programmable Function ButtonsOperator Conveniences Assigning Functions Beep FunctionSetting UP Alarm NotificationDisplay Dimmer Quick Data TransferOperator Conveniences Using Quick TransferConnections Transferring DataRecording Messages DRU-3 Digital Recording System OptionalMessage Playback Checking MessagesContinuous MULTI-CHANNEL Playback VS-2 Voice Synthesizer OptionalAltering INTER-MESSAGE Interval Transmitting Messages Manual TX/RXService MaintenanceService Note CleaningInternal Adjustments MaintenanceReference Frequency Calibration Problem Symptom Probable Cause Corrective Action TroubleshootingPress LSB/USB, CW/-R,FSK/-R, or SWR DRU-3 Optional AccessoriesPC-1A PG-2ZRemoving the Case Installing OptionsVS-2 Voice Synthesizer Unit DRU-3 Digital Recording UnitSO-2 TEMPERATURE-COMPENSATED Crystal Oscillator Tcxo Installing OptionsFSK, FM SpecificationsFSK, AM SpecificationsAppendix a Learning about DSP Information Appendix B PropagationNCDXF/IARU Beacon Network HF BeaconsFreq kHz Call Sign Receiver for Swling Appendix C General CoverageCommands Appendix D COM Connector ProtocolCommand Description Hardware DescriptionBAD Command Examples Parameter DescriptionParameter Table Types of Commands Computer Control CommandsTerminator Subtone Table for Format NO.14Command USE Precautions Error MessagesParameter Menu Selection Table for EX COMMAND, ParameterMenu Menu Item Command Tables Reading Command TablesBusy ID Identification Set Mixer RA RF Attenuator XIT DRS DSPTOR Sstv AGCFSK TOR Rtty SSB Sstv
Related manuals
Manual 28 pages 9.83 Kb Manual 104 pages 31.74 Kb

TS-870S specifications

The Kenwood TS-870S is a distinguished transceiver that stands out in the world of amateur radio, particularly for enthusiasts who seek a blend of advanced technology and user-friendly features. Introduced in the early 1990s, this HF transceiver quickly gained a reputation for its exceptional performance, versatility, and reliability, making it a favorite among operators worldwide.

One of the most noteworthy features of the TS-870S is its direct-sampling technology, which allows for superior signal fidelity and processing. This technology enables the transceiver to operate across a range of 160 meters to 10 meters, catering to both casual and serious operators. Its high-performance 16-bit digital signal processing (DSP) facilitates effective noise reduction and filtering capabilities, enhancing the overall clarity during transmission and reception.

In terms of power, the TS-870S boasts an output of 100 watts, providing ample power for various communication needs. The transceiver is equipped with an automatic antenna tuner, which simplifies the task of matching the antenna to the operating frequency, ensuring optimal performance without the hassle of manual adjustments.

Another significant aspect of the Kenwood TS-870S is its user interface, featuring a large, easy-to-read display, and a logically arranged control layout. This makes it accessible for both novice and experienced operators. The built-in memories allow for quick storage and access to favorite frequencies and settings, enhancing operational efficiency.

The Kenwood TS-870S also includes various advanced features such as an optional 2.4 kHz and 6 kHz roofing filter which provides improved performance in crowded band conditions. The receiver's dual VFOs (Variable Frequency Oscillators) enable simultaneous monitoring of two frequencies, which is particularly useful for operators who need to keep track of multiple signals or engage in cross-band communication.

Apart from its technical specifications, the TS-870S is constructed with durability in mind, ensuring that it can withstand the rigors of frequent use. It supports various operating modes, including SSB, CW, AM, and FM, making it a versatile choice for diverse amateur radio activities.

In conclusion, the Kenwood TS-870S combines advanced technology with user-friendly characteristics, offering amateur radio operators an exceptional tool for communication. With its innovative features, robust performance, and flexibility, it continues to be a respected choice among radio enthusiasts, solidifying its legacy in the realm of amateur radio.