Kenwood TS-870S instruction manual Reading Command Tables

APPENDICES ●

READING COMMAND TABLES

													w							u		i	o	!0
q
	AC			ANTENNA TUNER CONTROL
																						Parameter	Format	Parameter function
e	Function	Antenna Tuner THRU/IN -LINE, and tuning START/CANCEL																				P1	30	TUNE THRU/IN
																								(Answer Only)
																						P2	30	TUNE THRU/IN
r			Set		1		2		3	4	5	6	7	8	9	10	11	12	13		14
																						P3	1	TUNE OFF/ON
	Input					A		C		P2	P3	;
																					Note:
			Read		1		2		3	4	5	6	7	8	9	10	11	12	13			14
																						P1 is used for Answer only.
t						A		C	;
																						Tuning cannot be started if P2 is in the
																						THRU state (If P2="0", selecting "1" for P3
	Output		Answer		1		2		3	4	5	6	7	8	9	10	11	12	13		14
y																						does not start tuning).
						A		C	P1	P2	P3	;
																						P1: RX THRU/IN		P2: TX THRU/IN

qCommand

wName

eFunction of the command

rThe format of the command is shown. When oblique lines are drawn in the 1st and 2nd columns, there is no Set command.

tThe format of the command for reading the transceiver’s current status is shown. When oblique lines are drawn in the 1st and 2nd columns, there is no Read command.

yThe format of the command output from the transceiver is shown. When oblique lines are drawn in the 1st and 2nd columns, there is no Answer command.

uThe number of command digits is shown.

iCorresponds to the parameter of the command format.

oCorresponds to the Format number in the Parameter Table. For the parameter formats, refer to the Parameter Table {page 84}.

!0Indicates the function of the parameter.

COMMAND TABLES

Note: Parameters that have a Parameter Function of ÒNOT USEDÓ are not supported by the TS-870S. Any character except the ASCII control codes (00 to 1Fh) and the terminator (;) may be entered for those parameters.

AC			ANTENNA TUNER CONTROL
Function	Antenna Tuner THRU/IN -LINE, and tuning START/CANCEL
		Set		1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input					A	C		P2	P3	;
		Read		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					A	C	;
Output		Answer		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					A	C	P1	P2	P3	;

Parameter	Format	Parameter function
P1	30	TUNE THRU/IN
		(Answer Only)
P2	30	TUNE THRU/IN
P3	1	TUNE OFF/ON

Note:

P1 is used for Answer only.

Tuning cannot be started if P2 is in the THRU state (If P2="0", selecting "1" for P3 does not start tuning).

P1: RX THRU/IN P2: TX THRU/IN

AI		AUTO INFORMATION
																		Parameter	Format	Parameter function
Function	Auto information OFF/ON																	P1	32	AI NUMBER
																		Note:
																		For other commands, controls whether
	ReadSet		1		2	3	4	5	6	7	8	9	10	11	12	13	14	changing a parameter will or will not trigger
Input				A	I	P1	;											the corresponding Answer command
																		to be output.
			1		2	3	4	5	6	7	8	9	10	11	12	13	14	Ex:
				A	I	;
																		For IF, the Answer command is output
																		if the step frequency or RIT/XIT
Output	Answer		1		2	3	4	5	6	7	8	9	10	11	12	13	14
																		frequency is changed.
				A	I	P1	;

AG			AF GAIN
																			Parameter	Format	Parameter function
Function	Sets or reads AF gain.																		P1	31	AF GAIN
		Set		1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input					A	G		P1		;
		Read		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					A	G	;
Output		Answer		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					A	G		P1		;

AN			ANTENNA NUMBER
																			Parameter	Format	Parameter function
Function	Selects antenna connector ANT 1/ ANT 2.																		P1	33	ANTENNA
																					NUMBER
		Set		1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input					A	N	P1	;
		Read		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					A	N	;
Output		Answer		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					A	N	P1	;

89