Kenwood TS-870S Operating Aids AT-300 External Tuner Optional, Communication Parameters

Page 56
[\
AGC AUTO
CW

7 OPERATING AIDS

AT-300 EXTERNAL TUNER (OPTIONAL)

from another room, or, when coupled with other

Note:

commercially available products and where lawful, from

another city via a telephone connection.

◆The AT-300 must be connected while the transceiver power is switched OFF.

◆There is a 4 A fuse inside the TS-870S for the AT-300 Antenna Tuner.

1Press [ANT] to select Antenna 1.

2Press [THRU/AUTO].

•This places the tuner in the bypass state until tuning begins in the next step. If tuning fails, the tuner returns to the bypass state.

•[AT TUNE] is disabled if [THRU/AUTO] is not pressed.

3Press [AT TUNE].

•When tuning completes successfully, the AT TUNE light goes out, and “– AT – TX RX” lights.

•If tuning doesn’t finish within about 20 sec, an alarm sounds. You may stop the alarm and the tuning by pressing [AT TUNE]. The alarm can be either a triple beep or the Morse code “CHECK” depending on the Menu No. 37 (WARN. BP) setting.

•“RX” lights on the Display even if Menu No. 08 (RX AT) is OFF.

•Each time after changing frequency or after removing then restoring the power, you must press [AT TUNE] since there is no Preset data stored when using the external tuner.

COMPUTER TRANSCEIVER INTERFACE

The TS-870S interfaces easily with a computer. Computer interfaces on transceivers have encouraged the development of software applications by many companies.

Now available are electronic logbook applications that are partially self-completing. Information transferred between the transceiver and the computer is written into the logbook. These applications can automatically track awards and look up callbook information too.

Imagine using a mouse click to change your TS-870S to the correct DX frequency and mode of a DX station after the arrival of a report from your local DX packetcluster.

Efficient operating technique is the key to winning in pileups and is essential when operating contests.

Other applications can change your computer into an electronic console from which you can remotely control functions on the TS-870S without physically touching its Front Panel. This capability makes possible remote operation of your transceiver from across the room,

The list of applications is large and expanding, and is limited only by the imagination of software programmers. In short, the COM connector adds a new level of flexibility and opportunity to enjoy Amateur radio when a transceiver control application that supports the TS-870S and a computer are used.

Before using a computer for transceiver control, you should be aware of a few points. After you manually switch OFF the transceiver power, you can then switch ON the transceiver power using commands from the computer. Similarly, after switching OFF the power from the computer, it is then possible to switch ON the power from the Front Panel.

You can use the Front Panel controls while using computer control. Settings done from the Front Panel are effective immediately. After power is switched OFF from the computer, all values and settings per the Front Panel controls are restored.

COMMUNICATION PARAMETERS

In order to control the transceiver with your computer, you must first choose the communication parameters that you require. Configure your transceiver control application for 8 data bits and no parity. The communication speed and number of stop bits must match the settings in the TS-870S. The transceiver is configured via Menu No. 56 (COM.RATE). After changing Menu No. 56, the TS-870S must be switched OFF and then ON again for the new parameters to become effective. The defaults in the TS-870S are 9600 bps and 1 stop bit.

Menu No. 56

Baud Rate

Stop Bits

Setting

(bps)

 

12 1

1200

1

 

 

 

24 1

2400

1

 

 

 

48 1

4800

1

 

 

 

48 2

4800

2

 

 

 

96 1

9600

1

192 1

19200

1

384 1

38400

1

 

 

 

576 1

57600

1

 

 

 

Note:

◆Before connecting the TS-870S to a computer, switch OFF the power to the TS-870S and the computer.

◆To reliably use the 38400 or 57600 bps transfer rates, the serial port of your computer must support these high-speed communications parameters.

◆More information on controlling the TS-870S by a computer is included in Appendix D “COM CONNECTOR PROTOCOL” {page 83}.

50

Page 55 Page 57
Image 56
Page 55 Page 57
Contents TS-870S KEY2 Applicable ModelWriting Conventions Followed Power Sources Power Cable ProtectionPower Lines CleaningContents Scan Memory FeaturesRejecting Interference Maintenance Optional AccessoriesInstalling Options Specifications AppendicesDSP Maximum SIGNAL/ Minimum Noise FeaturesSupplied Accessories IntroductionTransmission Line MHz 14 MHz 30 MHz InstallationAntenna Connection DC Power Supply Connection InstallationGround Connection Lightning ProtectionRear Panel Accessory ConnectionsFront Panel Computer Interface COM Rtty Equipment Rtty and ACCLinear Amplifier Remote Pin FunctionSM-230 Station Monitor if OUT Accessory Equipment ACCAntenna Tuner AT Pin No. Pin Name ANO GND PSQ SmetPKS PKDYour First QSO First QSO Front Panel Getting Acquainted@5QUICK Memo MR button 6KEY Speed control@4QUICK Memo M.IN button @7Tuning control Enter buttonLSB/USB button CW/ÐR button#3BEAT Cancel button RX M.CH button#5TX EQ. button #6FILTER LO/WIDTH and HI/SHIFT controlsMicrophone $4RIT/XIT control$7M.CH/VFO.CH control UP/DWN buttonsRear Panel Display 0AUTO1PROC 2MONI5MENU 7SPLIT8RIT 9TONE#2ON AIR #3AT Tune#4FSK #7M.SCRSwitching Power ON/OFF Adjusting VolumeAdjusting Squelch Operating BasicsChanging Bands Selecting ModeOperating Basics Equalizing VFO Frequencies A=B Fine Tuning Quick ChangesOperating Basics Changing Step SizesMeter on Front Panel MeterOperating Basics Direct Frequency Entry Selecting Transmit Power TransmittingTransmit Carrier Level Microphone GainMenu Setup What is a MENU?Menu Access Temporary Menu ResettingMenu Configuration Menu SetupMenu Item Function Selections Default LO/WIDTH and HI/SHIFT controlsM.CH/VFO.CH control Setting Baud Rate bps Stop Bits Cross Reference for Menu Functions Communicating SSB TransmissionSlow Scan TV/ Facsimile Sstv FrequenciesSwitching TX/RX Manually CW TransmissionCommunicating TX SIDETONE/ RX Pitch FrequencySetting Delay Time Communicating Semi BREAK-INFull BREAK-IN CW Reverse ReceiveFunction Default Communicating Electronic KeyerActivity Consult KEY Speed controlMultiple-Button Functions Emulation OptionsStoring CW Messages CW Message PlaybackInquiry Command Description Erasing CW MessagesInquiry Functions To check an Inquiry function Press CH 3+CHFunction Commands Press CH 1+CHOption d Leading Other Nines Embedded FunctionsSerial Number Options FM Transmission FM Repeater OperationPress RX B or RX a Press RX a or RX BArrl 10-METER Band Plan Selecting Subtone FrequencyContinuous or Burst Subtones? Rtty Frequency Shift Keying AM TransmissionDigital Operation ERROR-CHECKING Modes AMTOR/ PACKET/ PACTOR/ G-TOR/ Clover Mode MeaningRtty Frequencies AmtorSPLIT-FREQUENCY Operation Packet FrequenciesCommunicating TF-SET Transmit Frequency SET Satellite OperationRIT Receive Incremental Tuning Operating AidsReceiving AGC Automatic Gain ControlXIT Transmit Incremental Tuning Operating AidsVOX VOICE-OPERATED Transmit Transmit InhibitMode Transmit Sampling Point Operating Aids Speech Processor SSB/AMChanging Frequency While Transmitting Transmit MonitorChanging Transmit Bandwidth Transmit BandshiftEqualizing Transmit Audio Microphone AGCAutomatic Mode Automatic Mode BoundariesUsing Automatic Mode Press MENU+Presetting Internal Tuner only Preset Bands for Internal TunerAutomatic Antenna Tuner Internal TunerMenu No Baud Rate Stop Bits Operating Aids AT-300 External Tuner OptionalCommunication Parameters Slope Tuning SSB/AM Rejecting InterferenceDSP Tools If Shift CWBeat Cancel SSB/AM Rejecting InterferenceAuto Notch SSB CW/FSK/FM Adaptive FiltersSetting Spac Time Noise BlankerAIP Advanced Intercept Point AttenuatorMemory Features Conventional or Quick MEMORY?Conventional Memory Memory Channel DataMemory Features Memory Channel RecallSplit-Frequency Channels Quick Channel SearchMemory Transfer Memory Channel ScrollTemporary Frequency Changes Memory \ VFO TransfersFull Reset Erasing Memory ChannelsChannel to Channel Transfers ChannelMemory Features Storing Scan Limits in CH Programmable VFO FunctionQuick Memory Storing Into Quick MemoryRecalling from Quick Memory Temporary Frequency ChangesScan Program ScanScan Hold Confirming START/END LimitsMemory Scan ScanBusy Frequency Stop ALL-CHANNEL ScanSetting Scan Speed Memory Channel LockoutMicroprocessor Reset Switching ANT 1/ ANTOperator Conveniences Programmable Function ButtonsBeep Function Operator Conveniences Assigning FunctionsAlarm Notification Setting UPDisplay Dimmer Quick Data TransferUsing Quick Transfer Operator ConveniencesConnections Transferring DataDRU-3 Digital Recording System Optional Recording MessagesMessage Playback Checking MessagesVS-2 Voice Synthesizer Optional Continuous MULTI-CHANNEL PlaybackAltering INTER-MESSAGE Interval Transmitting Messages Manual TX/RXMaintenance ServiceService Note CleaningReference Frequency Calibration Internal AdjustmentsMaintenance Troubleshooting Problem Symptom Probable Cause Corrective ActionPress LSB/USB, CW/-R,FSK/-R, or SWR Optional Accessories DRU-3PC-1A PG-2ZInstalling Options Removing the CaseVS-2 Voice Synthesizer Unit DRU-3 Digital Recording UnitInstalling Options SO-2 TEMPERATURE-COMPENSATED Crystal Oscillator TcxoSpecifications FSK, FMSpecifications FSK, AMAppendix a Learning about DSP Appendix B Propagation InformationNCDXF/IARU Beacon Network HF BeaconsFreq kHz Call Sign Appendix C General Coverage Receiver for SwlingAppendix D COM Connector Protocol CommandsCommand Description Hardware DescriptionParameter Table BAD Command ExamplesParameter Description Computer Control Commands Types of CommandsTerminator Subtone Table for Format NO.14Error Messages Command USE PrecautionsMenu Selection Table for EX COMMAND, Parameter ParameterMenu Menu Item Reading Command Tables Command TablesBusy ID Identification Set Mixer RA RF Attenuator XIT TOR DRSDSP AGC SstvFSK TOR Rtty SSB Sstv
Related manuals
Manual 28 pages 9.83 Kb Manual 104 pages 31.74 Kb

TS-870S specifications

The Kenwood TS-870S is a distinguished transceiver that stands out in the world of amateur radio, particularly for enthusiasts who seek a blend of advanced technology and user-friendly features. Introduced in the early 1990s, this HF transceiver quickly gained a reputation for its exceptional performance, versatility, and reliability, making it a favorite among operators worldwide.

One of the most noteworthy features of the TS-870S is its direct-sampling technology, which allows for superior signal fidelity and processing. This technology enables the transceiver to operate across a range of 160 meters to 10 meters, catering to both casual and serious operators. Its high-performance 16-bit digital signal processing (DSP) facilitates effective noise reduction and filtering capabilities, enhancing the overall clarity during transmission and reception.

In terms of power, the TS-870S boasts an output of 100 watts, providing ample power for various communication needs. The transceiver is equipped with an automatic antenna tuner, which simplifies the task of matching the antenna to the operating frequency, ensuring optimal performance without the hassle of manual adjustments.

Another significant aspect of the Kenwood TS-870S is its user interface, featuring a large, easy-to-read display, and a logically arranged control layout. This makes it accessible for both novice and experienced operators. The built-in memories allow for quick storage and access to favorite frequencies and settings, enhancing operational efficiency.

The Kenwood TS-870S also includes various advanced features such as an optional 2.4 kHz and 6 kHz roofing filter which provides improved performance in crowded band conditions. The receiver's dual VFOs (Variable Frequency Oscillators) enable simultaneous monitoring of two frequencies, which is particularly useful for operators who need to keep track of multiple signals or engage in cross-band communication.

Apart from its technical specifications, the TS-870S is constructed with durability in mind, ensuring that it can withstand the rigors of frequent use. It supports various operating modes, including SSB, CW, AM, and FM, making it a versatile choice for diverse amateur radio activities.

In conclusion, the Kenwood TS-870S combines advanced technology with user-friendly characteristics, offering amateur radio operators an exceptional tool for communication. With its innovative features, robust performance, and flexibility, it continues to be a respected choice among radio enthusiasts, solidifying its legacy in the realm of amateur radio.
Top Page Image Contents