Epson TM-S1000 specifications Dealer or a Seiko Epson service center for advice

Page 4

Shut down your equipment immediately if it produces smoke, a strange odor, or

 

unusual noise.

WARNING

Continued use may lead to fire. Immediately unplug the equipment and contact your

 

dealer or a Seiko Epson service center for advice.

Never attempt to repair this product yourself. Improper repair work can be dangerous.

Never disassemble or modify this product. Tampering with this product may result in injury or fire.

Do not allow foreign matter to fall into the equipment. Penetration by foreign objects may lead to fire.

If water or other liquid spills into this equipment, do not continue to use it. Continued use may lead to fire. Unplug the power cord immediately and contact your dealer or a Seiko Epson service center for advice.

If you open the DIP switch cover, be sure to close the cover and tighten the screw after adjusting the DIP switch.

Using this product with the cover open may cause fire or electric shock.

Do not use aerosol sprayers containing flammable gas inside or around this product.

Doing so may cause fire.

Cautions

Do not connect cables in ways other than those mentioned in this manual.

Different connections may cause equipment damage or fire. CAUTION Be sure to set this equipment on a firm, stable, horizontal surface.

The product may break or cause injury if it falls.

Do not use this product in locations subject to high humidity or dust levels. Excessive humidity and dust may cause equipment damage or fire.

Do not place heavy objects on top of this product. Never stand or lean on this product.

Equipment may fall or collapse, causing breakage and possible injury.

To ensure safety, unplug this product before leaving it unused for an extended period.

4

Image 4
Contents Setup Product OverviewHandling 411259105 Rev. ETrademarks For Safety Key to SymbolsDealer or a Seiko Epson service center for advice Manual Content Restriction of UseAbout this Manual Aim of the ManualContents Connecting the Scanner to the Host Computer Application Development InformationPage Features Single Pass ProcessingStandard Equipment Easy OperationFranking Cartridge Interface Product ConfigurationColor Attachments AccessoriesOptions For Multi Feed Models Part Names and FunctionsFor Single Feed Models Power Switch Cover Power SwitchFor All Models Power LED Green LED IndicatorsError LED Orange Document LED Green ConnectorsOffline Processing Modes High-speedConfirmation OverlapProcessing speed For 30 Dpm ModelFor 60 Dpm Model With overlap ConfirmationFor 90 Dpm Model Reading Operation High-speed mode Confirmation mode Selectable processesFranking process Ejection processSensors Paper SensorsEject sensor E Main pocket nearly full sensor FCover Open Sensors Scanner cover open sensor HOther Sensors Franking cartridge sensor JFranking cartridge position sensor K Hopper position sensor MMaintenance Counter Counter Counter type UnitError Status Recoverable ErrorsError LED flash code Error description Recovery measureError LED flash code Error description Unrecoverable Errors Error LED flash codeError Error description Compatibility with the TM-J9000/J9100Product Specifications CPUDpm documents per minute, dpi dots per inch 25.4 mm Scanner Specifications JpegPaper Specifications For multi feed models FrontFront Scannable AreaBack Micr Readable Area Area for Electric EndorsementArea for Franking Front or BackElectrical Characteristics Environmental ConditionsExternal Dimensions and Mass MassPage Installing the Scanner Flow of SetupImportant Notes on Installation Connecting the Scanner to the Host Computer Connecting the Power Supply Unit Use the AC adapter. C as the power supply unitPage Download Software and ManualsSoftware Description Manual TM-S1000 Utility Functions of the UtilityHandling Turning On/OffOpening the Covers Opening the Scanner CoverOpening the Franker Cover Franking Cartridge Installing and Replacing the Franking CartridgeImportant Notes on the Franking Cartridge Handling Pocket Guide Pulling Out the GuidesASF/SF Guide Flow of Single Pass Processing Processing DocumentsImportant Notes on Processing Documents Inserting Checks For multi feed modelsFor single feed models When the documents are ejected, remove the documents Ejecting ChecksCleaning Cleaning the Image ScannerCleaning the Micr Unit Do not use sticky cleaning sheetsRemoving a Paper Jam Preparing for Transport