Canon FB630U/FB636U manual Error Messages, Cause, Response

Page 56

A P P E N D I C E S

Error Messages

Error Message

Scanner is Not Detected

Cannot Communicate with Scanner

Minimum Memory Requirements Not Met. Retry after Increasing Free Memory.

Home Position Not

Detected

File Access Error (FB63U

Button Manager) Error

Code = 36

An error has occurred. (Sense Code=xx, Additional Sense Code=xx, Additional Code Condition=xx)

Cause

•USB cable not connected correctly.

•Scanning unit is locked (lock switch is not released)

•USB cable not connected correctly.

•Memory is insufficient for the required volume of the scanned image data.

•Lock not released.

•The lamp is burnt out.

•Plug-in Module CS-U is already installed.

•Another error has occurred.

Response

•Use the USB cable to connect the Macintosh to the scanner properly.

•Release the lock switch at the base of the scanner

•Ensure the USB cable is securely fastened to the Macintosh and scanner.

•Reduce the scan area to the minimum possible scope and lower the resolution and magnification settings for the output device.

•Close all application programs that are running other than Canon Photo.

•Increase the memory allocated to Canon Photo.

•After releasing the lock, temporarily disconnect the USB cable. Reconnect it and restart Plug-in Module CS-U 3.3.

•Contact your nearest Canon Customer Care Center.

•Reinstall after emptying the Trash.

•Note down the Sense Code, Additional Sense Code and error message and contact the nearest Canon Customer Care Center.

56

Image 56

Contents User’s Guide This page intentionally left blank About the Conventions Used in this Guide How to Use this GuideWhere to Look Table of Contents Appendices Control Panel Features Scanning Procedures E PPlug-in Module CS-U Special Features See the Results of Adjustments Immediately Dynamic PreviewGamma Curve Adjusts Image Brightness Supports ColorSync 2.0 or higher Auto Tone CorrectionInstalling Plug-in Module CS-U Quick Start InstructionsStart Plug-in Module CS-U Start the Preview ScanSet the preferences, magnification and scan mode settings Specify the Area of the Image to be Scanned pClick the Browser button Select the area to be scanned by clicking and draggingScan the Image p Click the Scan buttonSave the image with the application software, specifying a Folder, file name and file formatE P Display Plug-in Module CS-U Control Panel E PE P Operating Procedures Canon PhotoClick the Preview button PreviewingSet the original on the scanner document glass Set Preferences UnitE P Setting Basic Resolution Preview Window Settings Dialog Box E P Preview Window SizeReturn to Default Settings ProceduresE P Calibration Select the Prefs menu in the control panelOutput Device Resolution= 360 dpi, Magnification= 100% Set MagnificationE P To Set the Magnification Factor Set the desired magnification factor on the control panelSet Scan Mode Black & WhiteDiffusion Dither GrayscaleColor High Definition ColorTo Set the Scan Mode Select the scan mode that you wantVerify Image Before Scanning To Verify the ImageE P Scanning Scan Area Settings Position the pointer in the preview windowSelect the area you want to enlarge with the zoom function ZoomingTo Zoom Click the Zoom In button To return to normal view, click the Zoom Out buttonSpecify the Scan Area ScanningTo Initiate the Scan Saving Scanned Images To Save an ImageColor/High Definition Mode Grayscale ModeBlack & White Mode Diffusion DitherHow to Adjust Histograms Using the Histogram Feature to Adjust Image ContrastHow to Interpret Histograms E P To Adjust a Histogram Click the Histogram buttonClick the Auto button Click the OK buttonAdjusting the Image with Gamma Settings Setting the GammaGamma = GammaBrightness Brightness and Contrast SettingsContrast E P To Adjust the Brightness and Contrast Click the Gamma buttonAdjusting Gamma with the Menu CRT Type aCRT Type B CRT Type CE P To Change the Gamma Value Settings Click the radio button for Menu SettingSending Output to a Printer Gamma Value SettingsAdjusting the Gamma Value to Match the Display Slider Tone Curve Settings Manipulating the GraphE P To Edit the Tone Curve Auto Tone Correction ColorSync To Activate the ColorSync FunctionOpen the Image menu and select Descreen ProcedureDescreen To Set the Threshold Value Set the threshold value in the Control PanelSaving / Recalling Settings To Save Settings in a Settings FileE P To Recall a Settings File Editing Scanned Images Many special effects may be achieved with filtersScanning Techniques Matching Scan Resolution to PurposeOptical and Enhanced Resolutions System Requirements SpecificationsFunctional Specifications Clicked on the Plug-in Module CS-U control panel TroubleshootingProblem Scan button cannot be selected Error Messages Error MessageCause ResponseGlossary Resolution Image FilePreview ScannerIndex P E N D I C E S Canon Customer Care Center Mail support via Canon Computer Systems, IncOE-030AA 0799 CDS Canon Inc