Datalogic Scanning 1000I manual Disable/Enable Pharmacode

Page 103

Pharmacode 39

Pharmacode 39

The following options apply to the Pharmacode 39 symbology.

Disable/Enable Pharmacode 39

When this feature is disabled, the scanner will not read Pharmacode 39 bar codes.

START / END

PROGRAMMING BARCODES

Disable Pharmacode 39

DEFAULT

Enable Pharmacode 39

Start/Stop Characters

Enables or disables transmission of Pharmacode 39 start/stop characters.

START / END

PROGRAMMING BARCODES

Don’t Transmit Start/Stop Characters

DEFAULT

Transmit Start/Stop Characters

Product Reference Guide

5-29

Image 103

Contents Magellan Datalogic Scanning, Inc Table of Contents Magellan Iii IBM USB Manual Conventions About This ManualAn approved A/C Adapter as shown in . For Connecting the ScannerUsing the Programming Bar Codes Resetting the Standard Product DefaultsProgramming LED and Beeper Indicators Error Error CodesGetting Started Double Read Timeout General FeaturesGeneral Features Productivity Index Reporting PIR Label Gone TimeoutSleep Mode Minutes Power On Alert LED and Beeper IndicatorsGood Read When to Indicate Good Read Beep Frequency Good Read Beep ControlSpecifies the duration of a good read beep Good Read Beep LengthGood Read Beep Volume Target Mode Active Time Scanning FeaturesTargeted Scanning Mode Target Mode Linger Time Wake Up Intensity 13% 14% 15% Interface Related Features Keyboard Wedge Interface Reference Interface Selection Keyboard Wedge H Keyboard Wedge J ³ 0 0 0 1 3 B Interface Selection Obey/Ignore Host Commands Interface FeaturesHost Transmission Buffers Interface FeaturesRS-232 Interface Features Data Bits Hardware Flow Control Intercharacter Delay Software Flow Control Disables/Enables software control using XON/XOFF charactersHost Echo Host Echo Quiet Interval Signal Voltage Normal/TTL Beep on Ascii BEL RS-232 InvertBeep on Not on File ACK NAK Options ACK Character RS-232 Interface Features cont.NAK Character ACK NAK Timeout Value Retry on ACK NAK TimeoutACK NAK Retry Count ACK NAK Error Handling Transmission Failure Indication IBM-USB Interface FeaturesIBM-USB Device usage IBM Transmit Labels in Code 39 Format IBMWand Emulation Supported SymbologiesWand Emulation Bar Code Format Wand Idle State Bar/Space PolarityTransmit Trailing Noise Signal SpeedTransmit Leading Noise Symbology ConversionKeyboard Wedge USB Keyboard Keyboard Wedge Caps Lock State Power-On Simulation Vided for each available scancode set. Reference pings Wedge Quiet Interval Intercharacter Delay Please Keep In Mind Data Editing OverviewGlobal Prefix/Suffix Scan the END bar code to exit Programming ModeDefault Setting Suffix 0D CR AIM ID Label ID Position Options Label IDLabel ID Position Before Bar Code Data Default Setting for this Feature FF 4646 hex Default Setting for this Feature I 49 hex Default Setting for this Feature G8 4738 hex Default Setting for this Feature % 25 hex Case Conversion 41423132FFFFFFFF Character ConversionDisable/Enable UPC-A SymbologiesCheck Digit Transmission UPC-AExpand UPC-A to EAN-13 UPC-A Minimum Reads Number System TransmissionUPC-A In-store Minimum Reads UPC-E Disable/Enable UPC-ENumber System Digit UPC-EExpand to UPC-E to UPC-A Minimum Reads Expand UPC-E to EAN13Expand UPC/EAN to Gtin GtinEAN-13 Disable/Enable EAN-13Isbn EAN-13 Flag 1 CharacterMinimum Reads EAN-8 Disable/Enable EAN-8EAN-8 Enable EAN Two-Label Add-ons Disable Optional 2-Digit Add-ons RSS-14 Disable/Enable RSS-14UCC/EAN 128 Emulation Minimum Reads RSS Expanded Disable/Enable RSS ExpandedLength Control RSS Expanded Length 1, Length 2 Programming Instructions Minimum Reads Code Disable/Enable CodeCheck Character Calculation Start/Stop Characters Check Character TransmitCode 39 Full Ascii Code Quiet Zones Code 39 Length 1, Length 2 Programming InstructionsCode 39 Stitching Pharmacode Disable/Enable PharmacodeCheck Character Transmit Transmit Function Characters Length Control Code 128 Conversion to Code Code 128 Length 1, Length 2 Programming InstructionsCode 128 Stitching Interleaved 2 Disable/Enable Interleaved 2Check Digit Calculation Check Digit Transmit Length Control Default Setting for this Feature Interleaved 2 of 5 Stitching Minimum Reads Codabar Disable/Enable CodabarCheck Character Verification Check Character Transmit Length Control Quiet Zones Codabar Length 1, Length 2 Programming InstructionsStart/Stop Character Transmission Start/Stop Character TypeCodabar Stitching Start/Stop Character MatchMinimum Reads Following options apply to the Code 93 symbology Length Control Code 93 Length 1, Length 2 Programming Instructions Code 93 Stitching MSI/Plessey Disable/Enable MSI/PlesseyCheck Digit Verification Number of Check Characters Length Control MSI/Plessey Length 1, Length 2 Programming Instructions MSI/Plessey Stitching Minimum Reads Standard 2 Disable/Enable Standard 2Check Digit Transmit Length Control Standard 2 of 5 Length 1, Length 2 Programming Instructions Standard 2 of 5 Stitching Minimum Reads Symbologies Optical and Read Performance Parameters Scanner DimensionsOther Parameters Physical PropertiesElectrical Parameters Environmental ParametersRS-232 Standard Cable Pinouts Primary Interface CablesIBM Port 5B/9B/17 USB & USB Keyboard IBM USBAlpha-Numeric Pad Alpha-Numeric Pad Interface Default Exceptions Defaults by SymbologyRS-232 Wincor/Nixdorf IBM InterfacesKeyboards Magellan Keyboard Model Cross Reference Keyboard Function Key MappingsTable E-2. Scanset 1 Function Key Map Table E-4.Scanset 3, 102-Key Function Key Map Table E-5. Scanset 3 122-Key Function Key Map Table E-6. Japanese DOS Function Key Map Table E-7. NEC 9801-Key Function Key Map Accepting RS-232 Commands Host CommandsMagellan Sample Symbols Sample Symbols Ascii Chart Datalogic Scanning, Inc

Related manuals

Manual 176 pages 51.63 Kb

Manual 44 pages 55.92 Kb