Datalogic Scanning 1000I manual Alpha-Numeric Pad

Page 143

Appendix C

Alpha-Numeric Pad

A

B

C

D

E

F

Product Reference Guide

C-1

Image 143

Contents Magellan Datalogic Scanning, Inc Table of Contents Magellan Iii IBM USB Manual Conventions About This ManualAn approved A/C Adapter as shown in . For Connecting the ScannerProgramming Resetting the Standard Product DefaultsUsing the Programming Bar Codes LED and Beeper Indicators Error Error CodesGetting Started Double Read Timeout General FeaturesGeneral Features Productivity Index Reporting PIR Label Gone TimeoutSleep Mode Minutes Power On Alert LED and Beeper IndicatorsGood Read When to Indicate Good Read Beep Frequency Good Read Beep ControlSpecifies the duration of a good read beep Good Read Beep LengthGood Read Beep Volume Targeted Scanning Mode Scanning FeaturesTarget Mode Active Time Target Mode Linger Time Wake Up Intensity 13% 14% 15% Interface Related Features Keyboard Wedge Interface Reference Interface Selection Keyboard Wedge H Keyboard Wedge J ³ 0 0 0 1 3 B Interface Selection Obey/Ignore Host Commands Interface FeaturesHost Transmission Buffers Interface FeaturesRS-232 Interface Features Data Bits Hardware Flow Control Intercharacter Delay Software Flow Control Disables/Enables software control using XON/XOFF charactersHost Echo Host Echo Quiet Interval Signal Voltage Normal/TTL Beep on Ascii BEL RS-232 InvertBeep on Not on File ACK NAK Options NAK Character RS-232 Interface Features cont.ACK Character ACK NAK Timeout Value Retry on ACK NAK TimeoutACK NAK Retry Count ACK NAK Error Handling IBM-USB Device usage IBM-USB Interface FeaturesTransmission Failure Indication IBM Transmit Labels in Code 39 Format IBMWand Emulation Bar Code Format Supported SymbologiesWand Emulation Wand Idle State Bar/Space PolarityTransmit Trailing Noise Signal SpeedTransmit Leading Noise Symbology ConversionKeyboard Wedge USB Keyboard Keyboard Wedge Caps Lock State Power-On Simulation Vided for each available scancode set. Reference pings Wedge Quiet Interval Intercharacter Delay Please Keep In Mind Data Editing OverviewGlobal Prefix/Suffix Scan the END bar code to exit Programming ModeDefault Setting Suffix 0D CR AIM ID Label ID Position Options Label IDLabel ID Position Before Bar Code Data Default Setting for this Feature FF 4646 hex Default Setting for this Feature I 49 hex Default Setting for this Feature G8 4738 hex Default Setting for this Feature % 25 hex Case Conversion 41423132FFFFFFFF Character ConversionDisable/Enable UPC-A SymbologiesExpand UPC-A to EAN-13 UPC-ACheck Digit Transmission UPC-A Minimum Reads Number System TransmissionUPC-A In-store Minimum Reads UPC-E Disable/Enable UPC-EExpand to UPC-E to UPC-A UPC-ENumber System Digit Minimum Reads Expand UPC-E to EAN13Expand UPC/EAN to Gtin GtinEAN-13 Disable/Enable EAN-13Isbn EAN-13 Flag 1 CharacterMinimum Reads EAN-8 Disable/Enable EAN-8EAN-8 Enable EAN Two-Label Add-ons Disable Optional 2-Digit Add-ons UCC/EAN 128 Emulation Disable/Enable RSS-14RSS-14 Minimum Reads RSS Expanded Disable/Enable RSS ExpandedLength Control RSS Expanded Length 1, Length 2 Programming Instructions Minimum Reads Check Character Calculation Disable/Enable CodeCode Start/Stop Characters Check Character TransmitCode 39 Full Ascii Code Quiet Zones Code 39 Length 1, Length 2 Programming InstructionsCode 39 Stitching Pharmacode Disable/Enable PharmacodeCheck Character Transmit Transmit Function Characters Length Control Code 128 Conversion to Code Code 128 Length 1, Length 2 Programming InstructionsCode 128 Stitching Check Digit Calculation Disable/Enable Interleaved 2Interleaved 2 Check Digit Transmit Length Control Default Setting for this Feature Interleaved 2 of 5 Stitching Minimum Reads Check Character Verification Disable/Enable CodabarCodabar Check Character Transmit Length Control Quiet Zones Codabar Length 1, Length 2 Programming InstructionsStart/Stop Character Transmission Start/Stop Character TypeCodabar Stitching Start/Stop Character MatchMinimum Reads Following options apply to the Code 93 symbology Length Control Code 93 Length 1, Length 2 Programming Instructions Code 93 Stitching Check Digit Verification Disable/Enable MSI/PlesseyMSI/Plessey Number of Check Characters Length Control MSI/Plessey Length 1, Length 2 Programming Instructions MSI/Plessey Stitching Minimum Reads Standard 2 Disable/Enable Standard 2Check Digit Transmit Length Control Standard 2 of 5 Length 1, Length 2 Programming Instructions Standard 2 of 5 Stitching Minimum Reads Symbologies Optical and Read Performance Parameters Scanner DimensionsOther Parameters Physical PropertiesElectrical Parameters Environmental ParametersIBM Port 5B/9B/17 Standard Cable Pinouts Primary Interface CablesRS-232 USB & USB Keyboard IBM USBAlpha-Numeric Pad Alpha-Numeric Pad Interface Default Exceptions Defaults by SymbologyRS-232 Wincor/Nixdorf IBM InterfacesKeyboards Magellan Keyboard Model Cross Reference Keyboard Function Key MappingsTable E-2. Scanset 1 Function Key Map Table E-4.Scanset 3, 102-Key Function Key Map Table E-5. Scanset 3 122-Key Function Key Map Table E-6. Japanese DOS Function Key Map Table E-7. NEC 9801-Key Function Key Map Accepting RS-232 Commands Host CommandsMagellan Sample Symbols Sample Symbols Ascii Chart Datalogic Scanning, Inc

Related manuals

Manual 176 pages 51.63 Kb

Manual 44 pages 55.92 Kb