Datalogic Scanning 1000I manual Good Read Beep Control, Good Read Beep Frequency

Page 20

General Features

Good Read Beep Control

This feature enables/disables the scanner’s ability to beep upon a successful decode of a bar code.

START / END

PROGRAMMING BARCODES

Disable

Enable

DEFAULT

Good Read Beep Frequency

Adjusts the good read beep to sound at a selectable low, medium or high frequency, selectable from the list below. (Controls the beeper’s pitch/tone.)

START / END

PROGRAMMING BARCODES

Low

Medium

DEFAULT

High

³0

0 1 4 0

2

2-8	Magellan® 1000i

Image 20

Contents Magellan Datalogic Scanning, Inc Table of Contents Magellan Iii IBM USB About This Manual Manual ConventionsConnecting the Scanner An approved A/C Adapter as shown in . ForProgramming Resetting the Standard Product DefaultsUsing the Programming Bar Codes LED and Beeper Indicators Error Codes ErrorGetting Started General Features Double Read TimeoutGeneral Features Label Gone Timeout Productivity Index Reporting PIRSleep Mode Minutes LED and Beeper Indicators Power On AlertGood Read When to Indicate Good Read Beep Control Good Read Beep FrequencyGood Read Beep Length Specifies the duration of a good read beepGood Read Beep Volume Targeted Scanning Mode Scanning FeaturesTarget Mode Active Time Target Mode Linger Time Wake Up Intensity 13% 14% 15% Interface Related Features Keyboard Wedge Interface Reference Interface Selection Keyboard Wedge H Keyboard Wedge J ³ 0 0 0 1 3 B Interface Selection Interface Features Obey/Ignore Host CommandsInterface Features Host Transmission BuffersRS-232 Interface Features Data Bits Hardware Flow Control Intercharacter Delay Disables/Enables software control using XON/XOFF characters Software Flow ControlHost Echo Host Echo Quiet Interval Signal Voltage Normal/TTL RS-232 Invert Beep on Ascii BELBeep on Not on File ACK NAK Options NAK Character RS-232 Interface Features cont.ACK Character Retry on ACK NAK Timeout ACK NAK Timeout ValueACK NAK Retry Count ACK NAK Error Handling IBM-USB Device usage IBM-USB Interface FeaturesTransmission Failure Indication IBM IBM Transmit Labels in Code 39 FormatWand Emulation Bar Code Format Supported SymbologiesWand Emulation Bar/Space Polarity Wand Idle StateSignal Speed Transmit Trailing NoiseSymbology Conversion Transmit Leading NoiseKeyboard Wedge USB Keyboard Keyboard Wedge Caps Lock State Power-On Simulation Vided for each available scancode set. Reference pings Wedge Quiet Interval Intercharacter Delay Data Editing Overview Please Keep In MindScan the END bar code to exit Programming Mode Global Prefix/SuffixDefault Setting Suffix 0D CR AIM ID Label ID Label ID Position OptionsLabel ID Position Before Bar Code Data Default Setting for this Feature FF 4646 hex Default Setting for this Feature I 49 hex Default Setting for this Feature G8 4738 hex Default Setting for this Feature % 25 hex Case Conversion Character Conversion 41423132FFFFFFFFSymbologies Disable/Enable UPC-AExpand UPC-A to EAN-13 UPC-ACheck Digit Transmission Number System Transmission UPC-A Minimum ReadsUPC-A In-store Minimum Reads Disable/Enable UPC-E UPC-EExpand to UPC-E to UPC-A UPC-ENumber System Digit Expand UPC-E to EAN13 Minimum ReadsGtin Expand UPC/EAN to GtinDisable/Enable EAN-13 EAN-13EAN-13 Flag 1 Character IsbnMinimum Reads Disable/Enable EAN-8 EAN-8EAN-8 Enable EAN Two-Label Add-ons Disable Optional 2-Digit Add-ons UCC/EAN 128 Emulation Disable/Enable RSS-14RSS-14 Minimum Reads Disable/Enable RSS Expanded RSS ExpandedLength Control RSS Expanded Length 1, Length 2 Programming Instructions Minimum Reads Check Character Calculation Disable/Enable CodeCode Check Character Transmit Start/Stop CharactersCode 39 Full Ascii Code Code 39 Length 1, Length 2 Programming Instructions Quiet ZonesCode 39 Stitching Disable/Enable Pharmacode PharmacodeCheck Character Transmit Transmit Function Characters Length Control Code 128 Length 1, Length 2 Programming Instructions Code 128 Conversion to CodeCode 128 Stitching Check Digit Calculation Disable/Enable Interleaved 2Interleaved 2 Check Digit Transmit Length Control Default Setting for this Feature Interleaved 2 of 5 Stitching Minimum Reads Check Character Verification Disable/Enable CodabarCodabar Check Character Transmit Length Control Codabar Length 1, Length 2 Programming Instructions Quiet ZonesStart/Stop Character Type Start/Stop Character TransmissionStart/Stop Character Match Codabar StitchingMinimum Reads Following options apply to the Code 93 symbology Length Control Code 93 Length 1, Length 2 Programming Instructions Code 93 Stitching Check Digit Verification Disable/Enable MSI/PlesseyMSI/Plessey Number of Check Characters Length Control MSI/Plessey Length 1, Length 2 Programming Instructions MSI/Plessey Stitching Minimum Reads Disable/Enable Standard 2 Standard 2Check Digit Transmit Length Control Standard 2 of 5 Length 1, Length 2 Programming Instructions Standard 2 of 5 Stitching Minimum Reads Symbologies Scanner Dimensions Optical and Read Performance ParametersPhysical Properties Electrical ParametersEnvironmental Parameters Other ParametersIBM Port 5B/9B/17 Standard Cable Pinouts Primary Interface CablesRS-232 IBM USB USB & USB KeyboardAlpha-Numeric Pad Alpha-Numeric Pad Defaults by Symbology Interface Default ExceptionsIBM Interfaces RS-232 Wincor/NixdorfKeyboards Magellan Keyboard Function Key Mappings Keyboard Model Cross ReferenceTable E-2. Scanset 1 Function Key Map Table E-4.Scanset 3, 102-Key Function Key Map Table E-5. Scanset 3 122-Key Function Key Map Table E-6. Japanese DOS Function Key Map Table E-7. NEC 9801-Key Function Key Map Host Commands Accepting RS-232 CommandsMagellan Sample Symbols Sample Symbols Ascii Chart Datalogic Scanning, Inc

Related manuals

Manual 176 pages 51.63 Kb

Manual 44 pages 55.92 Kb