Acer M11E manual System Board Layout with Network Connector

Page 20

1.2.1System Board Layout

1

2

19

20

21

22

3 4 5

6

7

8

9

18

17

16

15

14

13

12

11

10

1	PS/2 mouse port	12	AGP slot
2	PS/2 keyboard port	13	Battery
3	USB connectors	14	Intel 82371EB
4	Serial port 2	15	IDE1 connector
5	Parallel port	16	IDE2 connector
6	Serial port 1	17	FDD connector
7	RJ-45 connector	18	Intel 440BX
8	Intel 82C558 Ethernet controller	19	DIMM sockets
9	BIOS	20	Voltage regulators
10	ISA slots	21	CPU slot
11	PCI slots	22	Power connector

Figure 1-1 System Board Layout with Network Connector

1-4	User’s Guide

Image 20

Contents M11E System Copyright Important Safety Instructions Page Page CD ROM Safety Warning Vii FCC Class B Radio Frequency Interference Statement About this Manual Purpose Manual StructureConventions Table of Contents Bios Utility XiiXiii List of Figures XivList of Tables Page Features System BoardUser’s Guide Major Components System Board Layout with Network Connector System Board LayoutSystem Board Layout without Network Connector Jumpers and Connectors Jumper and Connector LocationsBlackened pin of a jumper or connector represents pin Jumper Settings Connector FunctionsJP1 ESD Precautions Installing the Pentium II processor Attaching the Processor Fan SinkRemoving tape protector from Fan SInk Locking a Wide Clip End 10 Locking the metal bracket Installing a Pentium II Processor 11 Installing the Pentium II Retention Mechanism12 Installing the Pentium II Retention Mechanism 13 Installing a Pentium II Processor Removing a Pentium II Processor 14 Securing the Pentium II Processor16 Removing the Pentium II Processor Memory Upgrade Memory ConfigurationsInstalling a Dimm 17 Installing a DimmRemoving a Dimm 18 Removing a DimmReconfiguring the System Installing Expansion Cards Installing PCI CardsInstalling ISA Cards Bios detects and configures only PnP cardsInstalling an AGP Card 20 Installing an ISA Card21 Installing an AGP Card System Error Messages Error MessagesSoftware Error Messages System Board Mmmmssssooo Wxxxx Correcting Error Conditions Page Setup Utility Entering Setup Setup UtilitySetup Utility System Information Internal Cache Size ProcessorProcessor Speed External Cache Floppy Drive aFloppy Drive B IDE Primary Channel MasterIDE Secondary Channel Slave Total MemorySerial Port Parallel Port15 PS/2 Mouse Product Information Product NameSystem S/N Main Board IDMain Board S/N System Bios VersionDMI Bios Version Disk Drives Floppy DrivesIDE Primary Channel Master 2 LS-120 Drive Compatible AsIDE Drives IDE Secondary Channel Slave IDE Primary Channel SlaveIDE Secondary Channel Master This parameter specifies the size of your hard disk, in MB Disabled Enhanced IDE FeaturesDMA Transfer Mode Base Address Onboard PeripheralsSerial Ports 1 ∙ 3BCh ∙ 378h ∙ 278h Onboard Device Settings Operation ModeFloppy Disk Controller IDE ControllerPS/2 Mouse Controller USB Host ControllerSMBus Interrupt IRQ9 Onboard Ethernet ChipIDE Hard Disk Standby Timer Power ManagementPower Management Mode Power Switch 4 sec System Sleep TimerModem Ring Indicator System Wake-up EventBoot Options Boot SequenceFirst Hard Disk Drive Fast BootSilent Boot Num Lock After Boot Configuration TableBoot from LANDesk Service Agent Memory TestDate and Time DateTime Advanced Options Memory/Cache OptionsMemory at 15MB-16MB Reserved for Internal Cache CPU CacheExternal Cache For system board with LAN Memory Parity Mode2 PnP/PCI Options PCI IRQ Setting For system board without LANPCI IRQ Sharing VGA Palette SnoopReset Resource Assignments CPU FrequencyGraphics Aperture Size Plug and Play OSProcessor Speed Bus FrequencyCPU Multiple System Security Setup PasswordTo set or change a Password Setup Utility To remove your Setup Password To bypass Setup Password Power-on Password Make sure to set JP3 to 1-2 to enable Power-on passwordDrive Control Settings Disk Drive ControlLoad Default Settings Abort Settings ChangeExit Setup